In 2017, Energinet and TenneT, the Danish and Dutch Transmission System Operators (TSOs), have announced the North Sea Wind Power Hub (NSWPH) project. The project aims at increasing by 36 GW the North Sea offshore wind capacity, with an artificial island collecting all the power produced by wind turbines and several HVDC links transmitting this power to the onshore grids. This project brings together new opportunities and new challenges, both from a technical and economic point of view. In this regard, this paper presents three analyses regarding the design and operation of such an offshore system. First, we perform a techno-economic assessment of different grid configurations for the collection of the power produced by wind farms and its transmission to the hub. In this analysis, two frequencies and two voltage levels for the operation of the offshore grid are investigated. Our findings show that the nominal-frequency high-voltage option is the more suitable, as lowfrequency does not bring any advantage and low-voltage would results in higher costs. The second analysis is related to the differences in operating the system with low- or zero-inertia; different dynamic studies are performed for each configuration to identify proper control actions and their stability properties. Comparing the outcomes of the simulations, we observed that voltage and frequency oscillations are better damped in the zero-inertia system; however, the risk of propagating offshore faults in the connected onshore grids is mitigated with the inclusion of the synchronous condensers. Lastly, a comparison of ElectroMagnetic Transient (EMT) and phasor-mode (also known as RMS) models is presented, in order to understand their appropriateness of simulating low- and zeroinertia systems. The results show that phasor approximation modelling can be used, as long as eigen-frequencies in power network are well damped.
Since time-domain simulations of wave energy converters are computationally expensive, how can we analyse their dynamics and test wide ranges of design variables, without simplifying the physics involved? One possible solution is the use of General Polynomial Chaos (gPC). GPC provides computationally efficient surrogate models for partial differential equation based models, which are particularly useful for sensitivity analysis and uncertainty quantification. We demonstrate the application of gPC to study the dynamics of a wave energy converter in an operational sea-state, when there is uncertainty in the values of the stiffness and damping coefficient of the power take-off.
A coupling between a dynamic mooring solver based on high-order finite element techniques (MooDy) and a radiation-diffraction based hydrodynamic solver (WEC-Sim) is presented. The high-order scheme gives fast convergence resulting in high-resolution simulations at a lower computational cost. The model is compared against a lumped mass mooring code (MoorDyn) that has an existing coupling to WEC-Sim. The two models are compared for a standard test case and the results are similar, giving confidence in the new WEC-Sim-MooDy coupling. Finally, the coupled model is validated using experimental data of a spread moored cylinder with good agreement.
A numerical model (MOODY) for the study of the dynamics of cables is presented in Palm et al. (2013), which was developed for the design of mooring systems for floating wave energy converters. But how does it behave when it is employed together with the tools used to model floating bodies? To answer this question, MOODY was coupled to a linear potential theory code and to a computational fluid dynamics code (OpenFOAM), to model small scale experiments with a moored buoy in linear waves. The experiments are well reproduced in the simulations, with the exception of second order effects when linear potential theory is used and of the small overestimation of the surge drift when computational fluid dynamics is used. The results suggest that MOODY can be used to successfully model moored floating wave energy converters.
Mooring systems are required to keep floating wave energy converters (WECs) on station. The mooring concept might impact the performance of the WEC, its cost and its integrity. With the aim of clarifying the pros and cons of different mooring designs, we present the results from physical model experiments of three different mooring concepts in regular and irregular waves, including operational and survival conditions. The parameters investigated are the tension in the cables, the motions of the device in the different degrees of freedom and the seabed footprint in each case. We can see that the mooring system affects the performance of the wave energy converter, but the magnitude of the impact depends on the parameter analysed, on the mode of motion studied and on the conditions of the sea. Moreover, different configurations have similar performances in some situations and the choice of one over another might come down to factors such as the type of soil of the seabed, the spacing desired between devices, or environmental impacts. The results of our experiments provide information for a better selection of the mooring system for a wave energy converter when several constraints are taken into account (power production, maximum displacements, extreme tensions, etc).
A novel damping system is developed to address offshore wind turbine tower vibration exacerbated by global warming-induced coastal extreme weather. Through parametric optimization, it stabilizes nacelle displacement under normal loads and reduces responses in diverse wind conditions: 18.8% max bending stress reduction during gusts, 26.3% nacelle displacement mitigation under high turbulence, and 7.9% displacement standard deviation reductions in 50-year extreme winds. A Norwegian wind farm extends tower life by 44% at the tower top and 99.36% at the tower base. Under varying gust angles, it reduces nacelle displacement (4.3%) and bottom bending moment (3.2%), enhancing structural stability. These demonstrate their potential to cut maintenance costs and extend lifetime, which is crucial for offshore wind turbine development.
Mooring failures significantly threaten the stability of Floating Offshore Wind Turbines (FOWT) under extreme environmental conditions. This study presents an innovative shared damping mooring system incorporating Seaflex dampers to improve structural stability and operational reliability. Dynamic simulations under 1-year and 50-year return period sea states demonstrate the system’s effectiveness. Under Ultimate Limit State (ULS) conditions, the system reduces surge displacement by 59%, pitch angle by 47%, and mooring line tension by 72%. Under Accidental Limit State (ALS) conditions, it mitigates load spikes, reduces drift displacement by 60%, and improves safety factors by 50%. The comparison shows chain and wire rope configurations have better load reduction performance in the shared damping scheme. Lightweight and adaptable, the Seaflex dampers enhance broad-spectrum damping without affecting platform buoyancy. This study provides a robust solution for improving FOWT safety and durability in harsh marine environments, enabling large-scale offshore wind energy development.
This study proposes a novel tower damping system to enhance the structural performance of the NREL 5 MW semi-submersible wind turbine under operational and extreme load conditions. Environmental load data from the Norwegian MET center was analyzed to characterize the loading conditions for floating offshore wind turbines (FOWT). The probability density spectrum of sea state data was employed to identify operational load conditions. At the same time, the Inverse First-Order Reliability Method (IFORM) was used to derive the 50-year extreme sea state. Perform a fully coupled Aero-Hydro-Servo-Elastic simulation of the FOWT dynamic model with a damping system using OrcaFlex software. The results reveal that: Under operational sea states, the turbine tower-top displacement was reduced by 60–70%, and acceleration by 30–40%, enhancing tower-top stability. Under extreme loads, tower-top acceleration was reduced by 5–7%, and displacement by 6–8%. Cumulative damage assessments indicate a reduction in fatigue damage of up to 72%, with the effective fatigue life of the tower base extended by 136%. The proposed damping system significantly reduces vibration under fatigue and extreme load conditions.
This study proposes a novel tower damping system to enhance the structural performance of the NREL 5 MW semi-submersible wind turbine under operational and extreme load conditions. Environmental load data from the Norwegian MET center was analyzed to characterize the loading conditions for floating offshore wind turbines (FOWT). The probability density spectrum of sea state data was employed to identify operational load conditions. At the same time, the Inverse First-Order Reliability Method (IFORM) was utilized to derive the 50-year extreme sea state. Perform a fully coupled Aero-Hydro-Servo-Elastic simulation of the FOWT dynamic model with a damping system using OrcaFlex software. The results reveal that: Under operational sea states, the turbine tower-top displacement was reduced by 60–70%, and acceleration by 30–40%, enhancing tower-top stability. Under extreme loads, tower-top acceleration was reduced by 5–7%, and displacement by 6–8%. Cumulative damage assessments indicate a reduction in fatigue damage of up to 72%, with the effective fatigue life of the tower base extended by 136%. The proposed damping system significantly reduces vibration under fatigue and extreme load conditions.