For design validation of offshore structures and conceptualisation of wave energy converters, physical model testing performed in wave basin laboratories is often applied. In such cases, knowledge about the wave conditions is of great significance. For validation of the wave condition in such tests, different methods for estimation of the directional wave spectra may be applied. However, different assumptions are imposed in the methods and deviations here from providing uncertainties in the results. The following paper quantifies the influence of nonlinear effects on the accuracy of the estimated directional wave spectra. This is done by analysis of idealised, synthetically generated waves based on second order wave theory and secondly with simplified amplitude dispersion included. The present analyzes show that the uncertainties of the directional wave spectra are proportional to the level of nonlinearity present in the wave field.
We numerically simulate the hydrodynamic response of a floating offshore wind turbine (FOWT) using CFD. The FOWT under consideration is a slack-moored 1:70 scale model of the UMaine VolturnUS-S semisubmersible platform. This set-up has been experimentally tested in the COAST Laboratory Ocean Basin at the University of Plymouth, UK. The test cases under consideration are (i) static equilibrium load cases, (ii) free decay tests and (iii) two focused wave cases with different wave steepness. The FOWT is modeled using a two-phase Navier-Stokes solver inside the OpenFOAM-v2006 framework. The catenary mooring is computed by dynamically solving the equations of motion for an elastic cable using the MoodyCore solver. The results of the static and decay tests are compared to the experimental values with only minor differences in motions and mooring forces. The focused wave cases are also shown to be in good agreement with measurements. The use of a one-way fluid-mooring coupling results in slightly higher mooring forces, but does not influence the motion response of the FOWT significantly.
The design of wave energy converters should rely on numerical models that are able to estimate accurately the dynamics and loads in extreme wave conditions. A high-fidelity CFD model of a 1:30 scale point-absorber is developed and validated on experimental data. This work constitutes beyond the state-of-the-art validation study as the system is subjected to 50-year return period waves. Additionally, a new methodology that addresses the well-known challenge in CFD codes of mesh deformation is successfully applied and validated. The CFD model is evaluated in different conditions: wave-only, free decay, and wave–structure interaction. The results show that the extreme waves and the experimental setup of the wave energy converter are simulated within an accuracy of 2%. The developed high-fidelity model is able to capture the motion of the system and the force in the mooring line under extreme waves with satisfactory accuracy. The deviation between the numerical and corresponding experimental RAOs is lower than 7% for waves with smaller steepness. In higher waves, the deviation increases up to 10% due to the inevitable wave reflections and complex dynamics. The pitch motion presents a larger deviation, however, the pitch is of secondary importance for a point-absorber wave energy converter.
Wave excitation tests on a fixed sphere with the center at the still water level were carried out with three different physical wave basin setups. The tests were completed as a continued effort of the working group OES Wave Energy Converters Modeling Verification and Validation to increase confidence in numerical models of wave energy converters by generation of accurate benchmarks datasets for numerical model validation. An idealized test case with wave excitation of a fixed sphere to be used with the benchmarks was formulated. The three investigated physical wave basin setups included: 1) a six degree-of-freedom load cell mounted to the top of the sphere, 2) a bending beam force transducer mounted to the top of the sphere, and 3) a system of six pretensioned wires mounted to the top and bottom of the sphere with force transducers attached to each wire. The aim of the present paper is to identify the best representation of the idealized test case. To this end, the three experimental setups are inter-compared in terms of dynamic properties, sensitivity, and disturbances of the water phase from the presence of measurement equipment. Low inter-experiment variability was disclosed, ie, 5-8% depending on wave-nonlinearity, indicating accurate representations of the idealized test case across all setups. Setup 3 was found to be the more accurate representation and further work with this setup to release a public benchmark dataset was planned.
With increasing demand for renewable energy resources, the development of alternative concepts is still ongoing. The wave energy sector is still in vast development on the way to contribute to the energy production world wide. The present study presents the development of the Exowave wave energy converter made so far. A numerical model has been established supported by wave flume tests performed at Aalborg University during the first phase of the development. Furthermore, a successful open sea demonstration has been performed on 7 meters of water at Blue Accelerator, Belgium, from which the concept has been proven. As part of the ongoing research, verification of the numerical model will be made through experimental testing in the wave tank of Aalborg University, and an open sea demonstration at 14 meters of water depth will be executed off the coast of Hanstholm, Denmark.
The increasing role of offshore wind power plants in the electricity generation mix in Turkey raises some critical grid operation issues. In this context, the grid code regulation concerning the penetration of large-scale offshore wind power plants into Turkey's power system has become a prominent factor in the development of a reliable grid operation. In this paper, a comprehensive benchmark for grid codes of the European countries that have large-scale offshore wind power plants and Turkey is performed by considering voltage regulation, frequency regulation, fault ride-through, and power quality features. The compatibility of the grid codes in terms of the minimum technical requirements is discussed to show the pros and cons. An elaborate assessment of the Turkish grid code reveals the technical properties that need to be improved. The rigorous state-of-the-art review indicates that active power control & frequency regulation, reactive power control & voltage regulation, and voltage ride-through capabilities should be clarified in detail for the Turkish grid code. With this background, various recommendations, key challenges, and future trends related to the improvement of technical requirements for the Turkish grid code for the integration of offshore wind power plants are highlighted to help researchers, plant owners, and system operators.
High-fidelity viscous computational fluid dynamics (CFD) models coupled to dynamic mooring models is becoming an established tool for marine wave-body-mooring (WBM) interaction problems. The CFD and the mooring solvers most often communicate by exchanging positions and mooring forces at the mooring fairleads. Mooring components such as submerged buoys and clump weights are usually not resolved in the CFD model, but are treated as Morison-type bodies. This paper presents two recent developments in high-fidelity WBM modelling: (i) a one-way fluid-mooring coupling that samples the CFD fluid kinematics to approximate drag and inertia forces in the mooring model; and (ii) support for inter-moored multibody simulations that can resolve fluid dynamics on a mooring component level. The developments are made in the high-order discontinuous Galerkin mooring solver MoodyCore, and in the two-phase incompressible Navier–Stokes finite volume solver OpenFOAM. The fluid-mooring coupling is verified with experimental tests of a mooring cable in steady current. It is also used to model the response of the slack-moored DeepCwind FOWT exposed to regular waves. Minor effects of fluid-mooring coupling were noted, as expected since this a mild wave case. The inter-mooring development is demonstrated on a point-absorbing WEC moored with a hybrid mooring system, fully resolved in CFD-MoodyCore. The WEC (including a quasi-linear PTO) and the submerged buoys are resolved in CFD, while the mooring dynamics include inter-mooring effects and the one-way sampling of the flow. The combined wave-body-mooring model is judged to be very complete and to cover most of the relevant effects for marine WBM problems.
In this paper, the impacts of large-scale OWPPs penetration on the Turkish power system are addressed. The grid compliance analyzes for the large-scale OWPP integration are carried out by using the grid connection criteria defined in the Turkish grid code. PV and QV curves are obtained to assess the effect of OWPP on the static voltage stability limit. Eight scenarios are conducted to analyze the effect of the OWPP on the static and dynamic characteristics of the power grid. To observe the large-scale OWPP impact on the voltage and frequency stability, transient events such as the outage of conventional power plants and three-phase to ground faults are applied. The results of the voltage and frequency stability analysis reveal that the Turkish grid remains stable after the integration of an 1800 MW OWPP. Furthermore, the Turkish system remains stable even in the event of an outage of the international transmission lines to Bulgaria and Greece.
There are many uncertainties associated with the estimation of extreme loads acting on a wave energy converter (WEC). In this study we perform a sensitivity analysis of extreme loads acting on the Uppsala University (UU) WEC concept. The UU WEC consists of a bottom-mounted linear generator that is connected to a surface buoy with a taut mooring line. The maximum stroke length of the linear generator is enforced by end-stop springs. Initially, a Variation Mode and Effect Analysis (VMEA) was carried out in order to identify the largest input uncertainties. The system was then modeled in the time-domain solver WEC-SIM coupled to the dynamic mooring solver Moody. A sensitivity analysis was made by generating a surrogate model based on polynomial chaos expansions, which rapidly evaluates the maximum loads on the mooring line and the end-stops. The sensitivities are ranked using the Sobol index method. We investigated two sea states using equivalent regular waves (ERW) and irregular wave (IRW) trains. We found that the ERW approach significantly underestimates the maximum loads. Interestingly, the ERW predicted wave height and period as the most important parameters for the maximum mooring tension, whereas the tension in IRW was most sensitive to the drag coefficient of the surface buoy. The end-stop loads were most sensitive to the PTO damping coefficient.
High-fidelity simulations using computational fluid dynamics (CFD) for wave-body interaction are becoming increasingly common and important for wave energy converter (WEC) design. The open source finite volume toolbox OpenFOAM® is one of the most frequently used platforms for wave energy. There are currently two ways to account for moving bodies in OpenFOAM: (i) mesh morph-ing, where the mesh deforms around the body; and (ii) an overlooked mesh method where a separate body mesh moves on top of a background mesh. Mesh morphing is computationally efficient but may introduce highly deformed cells for combinations of large translational and rotational motions. The overlooked method allows for arbitrarily large body motions and retains the quality of the mesh. However, it comes with a substantial increase in computational cost and possible loss of energy conservation due to the interpolation. In this paper we present a straightforward extension of the spherical linear interpolation (SLERP) based mesh morphing algorithm that increases the stability range of the method. The mesh deformation is allowed to be interpolated independently for different modes of motion, which facilitates tailored mesh motion simulations. The paper details the implementation of the method and evaluates its performance with computational examples of a cylinder with a moonpool. The examples show that the modified mesh morphing approach handles large motions well and provides a cost effective alternative to overlooked mesh for survival conditions.