The share of renewables in the power system is increasing rapidly. Large offshore wind power plants (OWPPs) are developed at a high pace and conventional fossil fuel-based plants are decommissioned. If the OWPP gets islanded due to any contingency or in the event of a blackout, the whole OWPP will be shutdown. This paper proposes a STATCOM with a battery storage that is located at the point of common connection to an OWPP to enable OWPP energization from a fully discharged state to operate in islanded mode. The STATCOM functionality provides fast and dynamic reactive power management and the battery unit provides active power balancing capability to regulate the frequency in the island. The concept is demonstrated through time-domain simulations on an OWPP model in PSCAD. The results confirm the technical feasibility of the system.
This paper presents the methods developed and key findings of the IWEC project performed by Ocean Harvesting Technologies AB (OHT). It aimed to reduce the levelized cost of energy (LCoE) of OHT’s wave energy converter InfinityWEC, by analysing how different key parameters impact cost and annual output using a model of a 100-MW array installation. Component-level cost functions were developed and mapped to key parameters and constraints of the system. A large number of system configurations were then evaluated with a numerically efficient 3 degree-of-freedom (DoF) nonlinear radiationdiffraction model in WEC-Sim along with OHT’s sea statetuned polynomial reactive control (PRC). The most promising configurations were identified and investigated in more detail. The configuration with the best LCoE were finally identified and analysed further, including estimation of the effect of changing the PRC to model predictive control, which resulted in 17-34% higher annual output and 12-23% lower LCoE. The final LCoE was found to be 93-162 EUR MWh at 100 MW installed capacity. An important finding from the study is that using simplified metrics such as CAPEX/ton was found to be irrelevant. Numerical wave tank testing, high-fidelity computational fluid dynamics (CFD), were used to tune the viscous drag of the 3 DoF WEC-Sim model. Applying verification and validation (V&V) techniques the CFD simulations showed a relatively large numerical uncertainty, but the average power and the motion responses were found to be sufficiently accurate.
We present a Spectral Element Fully Nonlinear Potential Flow (FNPF-SEM) model developed for the simulation of wave-body interactions between nonlinear free surface waves and impermeable structures. The solver is accelerated using an iterative p-multigrid algorithm. Two cases are considered: (i) a surface piercing box forced into vertical motion creating radiated waves and (ii) a rectangular box released above its equilibrium resulting in freely decaying heave motion. The FNPF-SEM model is validated by comparing the computed hydrodynamic forces against those obtained by a Navier-Stokes solver. Although not perfect agreement is observed the results are promising, a significant speedup due to the iterative algorithm is however seen.
This paper presents ISOPE's 2020 comparative study on the interaction between focused waves and a fixed cylinder. The paper discusses the qualitative and quantitative comparisons between 20 different numerical solvers from various universities across the world for a fixed cylinder. The moving cylinder cases are reported in a companion paper as part B (Agarwal, Saincher, et al., 2021). The numerical solvers presented in this paper are the recent state of the art in the field, mostly developed in-house by various academic institutes. The majority of the participants used hybrid modeling (ie, a combination of potential flow and Navier–Stokes solvers). The qualitative comparisons based on the wave probe and pressure probe time histories and spectral components between laminar, turbulent, and potential flow solvers are presented in this paper. Furthermore, the quantitative error analyzes based on the overall relative error in peak and phase shifts in the wave probe and pressure probe of all the 20 different solvers are reported. The quantitative errors with respect to different spectral component energy levels (ie, in primary, sub-, and superharmonic regions) capturing capability are reported. Thus, the paper discusses the maximum, minimum, and median relative errors present in recent solvers as regards application to industrial problems rather than attempting to find the best solver. Furthermore, recommendations are drawn based on the analysis.
The levelized costs of energy (LCoE) of wave power is still not fully competitive with other sources of renewable energy. However, wave energy is partly in a different phase than other renewable energy types and could thus contribute to a better predictability and smoothed power output. This work focuses on co-location of wave and wind power by investigating the intermittency of wind and waves power based on measured historical data from several hundreds of locations worldwide. Employing wind power curves and wave power matrices, the sites are evaluated based on several different metrics. The results indicate that there are several spots where wave power has a much lower intermittency than wind power providing reliable energy supply. Best sites for co-location in terms of energy yield were found in North-Western Europe. However, both wind and wave production have the same seasonal variability in these sites. Only a handful of sites found in California showed the possibility of seasonal power smoothing using the combination of wind and wave.
The share of renewables in the power system is increasing rapidly. Large offshore wind power plants (OWPPs) are developed at a high pace and conventional fossil fuel-based plants are decommissioned. Consequently, there will be a risk of insufficient amount of power plants providing black start functionality for system restoration after a black out. This paper proposes a STATCOM with a battery energy storage that is located at the point of common connection to an OWPP that together can provide a reliable black start service to the power grid. The concept is demonstrated by using time domain simulations in PSCAD. The STATCOM functionality provides fast and dynamic reactive power management and the battery unit provides active power balancing capability to maintain the frequency within a tolerable range specified by the system operator. The simulation results fulfill the success criteria for the black start and confirm its feasibility for practical implementation.
Highly accurate and precise heave decay tests on a sphere with a diameter of 300 mm were completed in a meticulously designed test setup in the wave basin in the Ocean and Coastal Engineering Laboratory at Aalborg University, Denmark. The tests were dedicated to providing a rigorous benchmark dataset for numerical model validation. The sphere was ballasted to half submergence, thereby floating with the waterline at the equator when at rest in calm water. Heave decay tests were conducted, in which the sphere was held stationary and dropped from three drop heights: a small drop height, which can be considered a linear case, a moderately nonlinear case, and a highly nonlinear case with a drop height from a position where the whole sphere was initially above the water. The precision of the heave decay time series was calculated from random and systematic standard uncertainties. At a 95% confidence level, uncertainties were found to be very low — on average only about 0.3% of the respective drop heights. Physical parameters of the test setup and associated uncertainties were quantified. A test case was formulated that closely represents the physical tests, enabling the reader to do his/her own numerical tests. The paper includes a comparison of the physical test results to the results from several independent numerical models based on linear potential flow, fully nonlinear potential flow, and the Reynolds-averaged Navier–Stokes (RANS) equations. A high correlation between physical and numerical test results is shown. The physical test results are very suitable for numerical model validation and are public as a benchmark dataset.
Floating Power Plant (FPP) develops a hybrid floating wind and wave energy device. Pitching Wave Energy Converters (WECs) interact with the supporting structure, amplifying the motion of the WECs within the design wave frequency range. In this work we focus on the effect of the chamber geometry – without the WEC – in amplifying the waves inside the chamber. The simulations are carried out using two-phase Navier-Stokes simulations. We investigate the wave propagation and the interaction between waves and the fixed support structure. The simulations are compared to experimental tests performed in the wave basin at Aalborg University.
In the present paper, the experimental data on wave run-up on slender monopiles from recently published small and large scale tests are reanalyzed using different methods for the wave analysis. The hypothesis is that the post processing has an impact on the results, due to limited depth and highly nonlinear waves in many of the tests. Thus, the identified maximum waves by a zero-down crossing analysis are highly influenced by the reflection analysis method as well as by bandpass filtering. The stagnation head theory with the run-up coefficient is adopted and new coefficients are presented. The hypothesis is verified, and the applied bandpass filter is identified as a large contributor to conservatism in previous studies, as the steep, nonlinear waves that produce the highest run-up can be heavily distorted by the bandpass filter.
Floating Power Plant is, together with several partners, preparing to design, build and test a scaled version of the complete so-called P80 device. The scaled model is to be tested in AAU's wave basin, SSPA's facilities, followed by at least one external facility. The model will be tested in combinations of wave, wind and current conditions with a view to validating the numerical models and to further develop the understanding of the interactions within the device. The purpose of this document is to gather information that is relevant to designing and building the physically scaled model, and to designing and executing the test campaign.