A numerical model (MOODY) for the study of the dynamics of cables is presented in Palm et al. (2013), which was developed for the design of mooring systems for floating wave energy converters. But how does it behave when it is employed together with the tools used to model floating bodies? To answer this question, MOODY was coupled to a linear potential theory code and to a computational fluid dynamics code (OpenFOAM), to model small scale experiments with a moored buoy in linear waves. The experiments are well reproduced in the simulations, with the exception of second order effects when linear potential theory is used and of the small overestimation of the surge drift when computational fluid dynamics is used. The results suggest that MOODY can be used to successfully model moored floating wave energy converters.
This study investigates the complex and still insufficiently understood interactions between ocean currents and offshore wind farms (OWFs), with a focus on local-scale hydrodynamic effects near individual wind turbine foundations. Despite growing interest in the environmental impacts of OWFs, empirical field data on local-scale current dynamics within wind farms remain sparse. This technical report describes the results from a field campaign, which was conducted within the Anholt OWF in the Kattegat over a 9-day period in August 2024.
Computational fluid dynamics (CFD) is becoming an increasingly popular tool in the wave energy sector, and over the last five years we have seen many studies using CFD. While the focus of the CFD studies have been on the validation phase, comparing numerically obtained results against experimental tests, the uncertainties associated with the numerical solution has so far been more or less overlooked. There is a need to increase the reliability of the numerical solutions in order to perform simulation based optimization at early stages of development. In this paper we introduce a well-established verification and validation (V&V) technique. We focus on the solution verification stage and how to estimate spatial discretization errors for simulations where no exact solutions are available. The technique is applied to the cases of a 2D heaving box and a 3D moored cylinder. The uncertainties are typically acceptable with a few percent for the 2D box, while the 3D cylinder case show double digit uncertainties. The uncertainties are discussed with regard to physical features of the flow and numerical techniques.
Slugging flow in offshore oil & gas multi-phase transportation pipelines cause big challenges as the flow regime induces flow and pressure oscillations in the multi-phase pipelines. The negative impacts of the most severe slugs are significant and thus the elimination of slugging flow in the pipelines is a highly investigated topic. To eliminate the slug in an online manner real-time slug detection methods are often required. Traditionally topside pressure transmitters upstream of a 3-phase separator have been used as the controlled variable. In this paper Electrical Resistivity Tomography (ERT) has been examined as an alternative to the traditional pressure transmitters. A lab-scaled testing facility has been constructed in order to obtain test data from an ERT transmitter with 12 probes. Different flow regimes have been generated by a pump and a compressor where 2-phase flow can be tested. Based on the results, the study concludes that the ERT is able to detect the slug very well when the oil and water are well mixed. Furthermore, the traditional pressure transmitters have the limitation that pressure variations can be caused by other operating conditions than slug, such as change in the back pressure from control valves. The biggest limitation using ERT is the lack of ability to distinguish between gas and oil, and thus the ERT can only be used as an effective slug detect measurement when the oil-to-water ratio is low.
The paper discusses the use of CFD simulations to analyse the parametric excitation of moored, full scale wave energy converters in six degrees of freedom. We present results of VOF-RANS and VOF-Euler simulations in OpenFOAM!R for two body shapes: (i) a truncated cylinder; and (ii) a cylinder with a smooth hemispherical bottom. Flow characteristics show large differences in smoothness of flow between the hull shapes, where the smoother shape results in a larger heave response. However the increased amplitude makes it unstable and parametric pitch excitation occurs with amplitudes up to 30". The responses in surge, heave and pitch (including the transition to parametric motion) are found to be insensitive to the viscous effects. This is notable as the converters are working in resonance. The effect of viscous damping was visible in the roll motion, where the RANS simulations showed a smaller roll. However, the roll motion was found to be triggered not by wave-body interaction with the incident wave, but by reflections from the side walls. This highlights the importance of controlling the reflections in numerical wave tanks for simulations with WEC motion in six degrees of freedom.
Chalk reservoirs, due to their high porosity and very low permeability, represent one of the most interesting cases for engineering studies of carbonates. They exhibit complex fluid-rock interactions because of their reactive surfaces and dense porous medium. The reinjection of produced water is an attractive strategy for managing wastewater flow from oil wells. However, the complex composition of produced water, the reactive nature of carbonate rocks, and their low permeability create challenges related to permeability loss.
This study examines the stages of permeability change during core flooding experiments up to the point of complete clogging. A distinctive feature of this study is the presence of residual oil in the core samples, which simulates real reservoir conditions during produced water reinjection. The presence of residual oil is an additional factor influencing the change in core permeability, but there is no clear consensus in the research community on its impact on permeability during produced water injection.
All experiments were conducted in a core flooding system simulating well conditions in terms of pressure (170 bar) and temperature (70 ◦C). Produced water samples from the Dan field were used to replicate the chemical and thermodynamic processes occurring in a real well. The experiments identified three stages of permeability change: an initial increase in permeability (+12%), a period of pressure stabilization, and a subsequent decrease in permeability (− 8%) due to the formation of inorganic precipitates within the core channels.
The primary objective of the experiments is to investigate the relationship between permeability changes and the stages of reinjection, with a focus on the effects of residual oil. The study focuses on identifying the processes occurring up to the point of complete clogging, considering the impact of residual oil saturation in the chalk core samples. Image analysis using scanning electron microscopy, particle size measurement with a zeta-potential meter, and thermodynamic scale formation modeling with ScaleCERE software were employed to explain these processes.
Three stages of permeability change were identified during the injection of 200 pore volumes of produced water: increased permeability (+12%), pressure stabilization, and decreased permeability (− 8%). The positive influence of residual oil saturation on the filtration and storage properties of the reservoir was established, due to the mobilization of chalk core particles. Additionally, the theory of core channel clogging during the reinjection of formation water by the formation of inorganic precipitates within the channels was confirmed.
Understanding the causes of permeability reduction that occurred during the stage of permeability decrease enables the development of water purification methods specifically targeted at the causes of rock clogging. Predicting the process of injecting a mixture of produced and seawater will help in interpreting the data during disposal operations by injecting formation water into an injection well, and it will allow for the selection of effective measures to mitigate the impact on the reservoir.
Floating Power Plant is, together with several partners, preparing to design, build and test a scaled version of the complete so-called P80 device. The scaled model is to be tested in AAU's wave basin, SSPA's facilities, followed by at least one external facility. The model will be tested in combinations of wave, wind and current conditions with a view to validating the numerical models and to further develop the understanding of the interactions within the device. The purpose of this document is to gather information that is relevant to designing and building the physically scaled model, and to designing and executing the test campaign.
This paper investigates the optimal control solution using MPC for a typical offshore topside de-oiling process. By considering the combination of the upstream three-phase gravity separator and the downstream de-oiling hydrocyclone set-up as one integrated plant, the plant-wide control problem is formulated and handled using MPC technology. The de-oiling dynamics of the hydrocyclone are estimated via system identification while the key dynamics of the considered gravity separator are modeled based on mass balance and experimental parameter estimation. The developed MPC solution is simulated and experimentally validated via a lab-scaled pilot plant. The comparison of performances of the MPC controlled system with those of a PID controlled system, which emulates the commonly deployed control solution in most current installations, shows the promising results in optimally balancing the gravity separator's (level) control and hydrocyclone's (PDR) control.
Injection of water into wells is a common practice in offshore oil and gas installations, and here as in many other industries the water has to be deaerated before it is sent through miles of pipelines to reduce the risk of corrosion in those pipelines and other downstream equipment. It requires extremely low concentrations of dissolved oxygen for the corrosion of metals to begin, and removing the dissolved oxygen is currently done in large vacuum deaeration towers, a highly energy demanding process, along with additional injection of chemical oxygen scavengers. In many instances these processes are controlled in a feed-forward manner, where the operators rely on infrequent sampling and corresponding measurements to control the process. The possibilities for optimization in this field are thus numerous. The main challenges are online measurements of dissolved oxygen and their use in feedback control. This article gives a brief review of the state-of-the-art and investigates the potential of using dissolved oxygen as a reliable feedback parameter, taking inspiration from onshore waste water industries which have been dealing with dissolved oxygen feedback control since the 1970's.
From the process control point of view, any reliable and online Oil-in-Water (OiW) measurement could provoke a brand new control paradigm for produced water treatment. However, the real-time OiW monitoring is still an open and ad-hoc situation in recent decades. The fundamental issue, ie, the OiW measurement is methodology dependent, leads to numerous challenges, such as (i) how to verify the reliability and accuracy of a specific methodology/instrument; (ii) how to handle and interpret the measured data in a most objective manner; and (iii) how to keep a cost-effective on-site calibration and maintenance under the harsh offshore conditions etc. The paper reports our latest achievements and observations in usage of fluorescence- and microscopybased OiW monitoring technologies for advanced Produced Water Treatment (PWT) control and evaluation, particularly by focusing on the de-oiling hydrocyclone installations.