With increasing demand for renewable energy resources, the development of alternative concepts is still ongoing. The wave energy sector is still in vast development on the way to contribute to the energy production world wide. The present study presents the development of the Exowave wave energy converter made so far. A numerical model has been established supported by wave flume tests performed at Aalborg University during the first phase of the development. Furthermore, a successful open sea demonstration has been performed on 7 meters of water at Blue Accelerator, Belgium, from which the concept has been proven. As part of the ongoing research, verification of the numerical model will be made through experimental testing in the wave tank of Aalborg University, and an open sea demonstration at 14 meters of water depth will be executed off the coast of Hanstholm, Denmark.
There has been a continued increase in the load on the current offshore oil and gas de-oiling systems that generally consist of three-phase gravity separators and de-oiling hydrocyclones. Current feedback control of the de-oiling systems is not done based on de-oiling efficiency, mainly due to lack of real-time monitoring of oil-in-water concentration, and instead relies on an indirect method using pressure drop ratio control. This study utilizes a direct method where a real-time fluorescence-based instrument was used to measure the transient efficiency of a hydrocyclone combined with an upstream gravity separator. Two control strategies, a conventional PID control structure and an H ∞ robust control structure, both using conventional feedback signals were implemented, and their efficiency was tested during severely fluctuating flow rates. The results show that the direct method can measure the system's efficiency in real time. It was found that the efficiency of the system can be misleading, as fluctuations in the feed flow affect the inlet concentration more than the outlet oil concentration, which can lead to a discharge of large oil quantities into the ocean.
This article is a feasibility study on using fluorescence-based oil-in-water (OiW) monitors for on-line dynamic efficiency measurement of a deoiling hydrocyclone. Dynamic measurements are crucial in the design and validation of dynamic models of the hydrocyclones, and to our knowledge, no dynamic OiW analysis of hydrocyclones has been carried out. Previous studies have extensively studied the steady state efficiency perspective of hydrocyclones, and have related them to different key parameters, such as the pressure drop ratio (PDR), inlet flow rate, and the flow spill. Through our study, we were able to measure the dynamics of the hydrocyclone's efficiency (ϵ) response to step changes in the inlet flow rate with high accuracy. This is a breakthrough in the modelling, control, and monitoring of hydrocyclones.
Life depends on healthy oceans that provide ecosystem services (ES) to humans, including provisioning, regulating, supporting, and cultural ES (Kovalenko et al., 2023). However, biodiversity, habitats, and the delivery of marine ES and resources are increasingly threatened by growing human activities in the oceans (Worm et al., 2006). Blue-growth activities, such as shipping and energy, eutrophication, and climate change represent major pressures that affect marine ecosystems (Halpern et al., 2008; Ehlers, 2016). Over the past two decades, increasing scientific attention has focused on the need to preserve and restore healthy marine waters and their role in adapting to climate change (Santos et al., 2020). This challenge calls for holistic approaches that advance our knowledge. Within the contributions to this Research Topic (see Figure 1), three themes are central to driving further research to expand our understanding in this interdisciplinary field.
As more offshore wind energy projects are implemented, the risk of interactions between farms becomes more pronounced. While reduced surface roughness over water enhances airflow stability, it can also extend wake effects on downstream turbines. The study aims to enhance the understanding of wake interactions and efficiency variations based on the distance between neighboring farms. To assess the impact of neighboring farms across different scenarios and features, a methodology is developed to achieve computational optimality using an open-source Python-based library, PyWake, then verified by a well-established CFD software, Meteodyn. Then, the methodology is applied to a Brazilian offshore wind project currently under licensing as a reference point. The results indicate a 1–3% reduction in Annual Energy Production following the current Brazilian regulation for onshore projects of 20 times the blade tip height, as the minimum distance. This reduction translates to an approximate 3% increase in the Levelized Cost of Energy and a nearly 24% decrease in Net Present Value. These findings are crucial for offshore wind energy planning and its sustainable growth, indicating the need to define a minimum distance for the regulatory bodies. This would not only avoid future disputes but also enhance investor confidence.
An increasing water to oil ration in the North Sea oil and gas production motivates for an optimization of the current deoiling facilities. Current facilities are operated on matured methodologies, which in most cases fulfill the government regulations. However, it has also observed that these solutions could be further improved. In order to more precisely monitor the deoiling operations, this study investigated the real-time monitoring of the deoiling efficiency of the hydrocyclone facilities which are commonly used in offshore oil and gas production. Fluorescence based monitors were applied to measure hydrocyclone inlet's and underflow's Oil-in-Water (OiW) concentrations in real-time. Image-based microscopy was used to analyze the oil droplet size distribution at inlet and underflow to investigate the droplets' influence on hydrocyclone's efficiency. Performance experiments were carried out to identify how pressure difference ratio (PDR) and the droplet's sizes affect the deoiling efficiency. The performance of the deoiling hydrocyclone was significantly influenced by the inlet flow rate, while less or marginally dependent on the PDR. The droplet size distribution experiment proved that large droplets have a high probability to be separated by the hydrocyclone. The findings suggest that the coupled separator tank and hydrocyclone system can be further improved upon by deploying coordinated control as the two systems are strongly interdependent.
A major challenge in next-generation industrial applications is to improve numerical analysis by quantifying uncertainties in predictions. In this work we present a formulation of a fully nonlinear and dispersive potential flow water wave model with random inputs for the probabilistic description of the evolution of waves. The model is analyzed using random sampling techniques and nonintrusive methods based on generalized polynomial chaos (PC). These methods allow us to accurately and efficiently estimate the probability distribution of the solution and require only the computation of the solution at different points in the parameter space, allowing for the reuse of existing simulation software. The choice of the applied methods is driven by the number of uncertain input parameters and by the fact that finding the solution of the considered model is computationally intensive. We revisit experimental benchmarks often used for validation of deterministic water wave models. Based on numerical experiments and assumed uncertainties in boundary data, our analysis reveals that some of the known discrepancies from deterministic simulation in comparison with experimental measurements could be partially explained by the variability in the model input. Finally, we present a synthetic experiment studying the variance-based sensitivity of the wave load on an offshore structure to a number of input uncertainties. In the numerical examples presented the PC methods exhibit fast convergence, suggesting that the problem is amenable to analysis using such methods.
Large volumes of produced water are being discharged globally as byproducts of oil production. Commercial production chemicals are conventionally needed to avoid problems such as bacterial growth, pipe corrosion, and oil/water separation issues. These chemicals will partition between oil and water phases and may affect both treatment processes and the environmental impact when water is discharged to the ocean after treatment. Capillary zone electrophoresis is used to measure partitioning coefficients of oilfield chemicals when these are dissolved in the water phase and in contact with either octanol or crude oil. The technique is fast and, due to simplicity, could have merits as on-site assessment of the partition coefficient for direct assessment of the fate of chemicals. The method was first qualified by estimating partitioning coefficients of aliphatic carboxylic acids and chemicals with a molecular structure similar to those of some production chemicals. Subsequently, the coefficients were determined for two different commercial corrosion inhibitors and a biocide that are used in the oilfield as production chemicals. The results showed that the chemicals predominantly preferred to remain in the water phase after contact with either octanol or crude oil. The partitioning coefficients log(p) spanned between −0.36 and −1.68 in the case of water/octanol contact and between 2.68 and −1.41 in the case of water/crude oil contact. One of the corrosion inhibitors exhibited a significant difference in the partitioning depending on whether the organic phase was octanol or crude oil. The chemical had a preference for the water phase in the case of the former but a preference for the crude oil phase in the case of the latter. The result demonstrates that it makes it challenging to evaluate the use of partitioning coefficients for oilfield applications.
Our recent experimental investigations of flexible side-by-side blades under both steady and unsteady flows have observed flutter in both scenarios. Flutter significantly impacts blade kinematics and the hydrodynamic drag experienced by the blades. Our numerical approach [1], utilizing the reactive force model, successfully reproduces flutter phenomena. In contrast, the traditional Morison’s equation fails to trigger flutter. In the static regime where flutter does not occur, the bulk drag coefficients calibrated from experiments in steady and unsteady flows can be unified through an effective Cauchy number, allowing for the use of analytical models developed for steady flows in unsteady flows. In the flutter regime, using the bulk drag coefficient from steady flows underestimates the drag load in oscillatory flow.
Mooring systems are required to keep floating wave energy converters (WECs) on station. The mooring concept might impact the performance of the WEC, its cost and its integrity. With the aim of clarifying the pros and cons of different mooring designs, we present the results from physical model experiments of three different mooring concepts in regular and irregular waves, including operational and survival conditions. The parameters investigated are the tension in the cables, the motions of the device in the different degrees of freedom and the seabed footprint in each case. We can see that the mooring system affects the performance of the wave energy converter, but the magnitude of the impact depends on the parameter analysed, on the mode of motion studied and on the conditions of the sea. Moreover, different configurations have similar performances in some situations and the choice of one over another might come down to factors such as the type of soil of the seabed, the spacing desired between devices, or environmental impacts. The results of our experiments provide information for a better selection of the mooring system for a wave energy converter when several constraints are taken into account (power production, maximum displacements, extreme tensions, etc).