The International Energy Agency Technology Collaboration Program for Ocean Energy Systems (OES) initiated the OES Wave Energy Conversion Modeling Task, which focused on the verification and validation of numerical models for simulating wave energy converters (WECs). The long-term goal is to assess the accuracy of and establish confidence in the use of numerical models used in design as well as power performance assessment of WECs. To establish this confidence, the authors used different existing computational modeling tools to simulate given tasks to identify uncertainties related to simulation methodologies: (i) linear potential flow methods; (ii) weakly nonlinear Froude–Krylov methods; and (iii) fully nonlinear methods (fully nonlinear potential flow and Navier–Stokes models). This article summarizes the code-to-code task and code-to-experiment task that have been performed so far in this project, with a focus on investigating the impact of different levels of nonlinearities in the numerical models. Two different WECs were studied and simulated. The first was a heaving semi-submerged sphere, where free-decay tests and both regular and irregular wave cases were investigated in a code-to-code comparison. The second case was a heaving float corresponding to a physical model tested in a wave tank. We considered radiation, diffraction, and regular wave cases and compared quantities, such as the WEC motion, power output and hydrodynamic loading.
We present recent progress on the development of a new fully nonlinear potential flow (FNPF) model for estimation of nonlinear wave-body interactions based on a stabilized unstructured spectral element method (SEM). We introduce new proof-of-concepts for forced nonlinear wave-body interaction in two spatial dimensions to establish the methodology in the SEM setting utilizing dynamically adapted unstructured meshes. The numerical method behind the proposed methodology is described in some detail and numerical experiments on the forced motion of (i) surface piercing and (ii) submerged bodies are presented.
This paper presents the design and development of a conceptual prototype of an autonomous self-driven inline inspection robot, called Smart-Spider. The primary objective is to use this type of robot for offshore oil and gas pipeline inspection, especially for those pipelines where the conventional intelligent pigging systems could not or be difficult to be deployed. The Smart-Spider, which is real-time controlled by its own on-board MCU core and power supplied by a hugged-up battery, is expected to execute pipeline inspection in an autonomous manner. A flexible mechanism structure is applied to realize the spider's flexibility to adapt to different diameters of pipelines as well as to handle some irregular situations, such as to pass through an obstructed areas or to maneuver at a corner or junction. This adaptation is automatically controlled by the MCU controller based on pressure sensors' feedback. The equipped devices, such as the selected motors and battery package, as well as the human-and-machine interface are also discussed in detail. Some preliminary laboratory testing results illustrated the feasibility and cost-effectiveness of this design and development in a very promising manner.
The offshore de-oiling process is a vital part of current oil recovery, as it separates the profitable oil from water and ensures that the discharged water contains as little of the polluting oil as possible. With the passage of time, there is an increase in the water fraction in reservoirs that adds to the strain put on these facilities, and thus larger quantities of oil are being discharged into the oceans, which has in many studies been linked to negative effects on marine life. In many cases, such installations are controlled using non-cooperative single objective controllers which are inefficient in handling fluctuating inflows or complicated operating conditions. This work introduces a model-based robust H ∞ control solution that handles the entire de-oiling system and improves the system’s robustness towards fluctuating flow thereby improving the oil recovery and reducing the environmental impacts of the discharge. The robust H ∞ control solution was compared to a benchmark Proportional-Integral-Derivative (PID) control solution and evaluated through simulation and experiments performed on a pilot plant. This study found that the robust H ∞ control solution greatly improved the performance of the de-oiling process.
The paper discusses the use of CFD simulations to analyse the parametric excitation of moored, full scale wave energy converters in six degrees of freedom. We present results of VOF-RANS and VOF-Euler simulations in OpenFOAM!R for two body shapes: (i) a truncated cylinder; and (ii) a cylinder with a smooth hemispherical bottom. Flow characteristics show large differences in smoothness of flow between the hull shapes, where the smoother shape results in a larger heave response. However the increased amplitude makes it unstable and parametric pitch excitation occurs with amplitudes up to 30". The responses in surge, heave and pitch (including the transition to parametric motion) are found to be insensitive to the viscous effects. This is notable as the converters are working in resonance. The effect of viscous damping was visible in the roll motion, where the RANS simulations showed a smaller roll. However, the roll motion was found to be triggered not by wave-body interaction with the incident wave, but by reflections from the side walls. This highlights the importance of controlling the reflections in numerical wave tanks for simulations with WEC motion in six degrees of freedom.
This paper analyzes the nonlinear forces on a moored point-absorbing wave energy converter (WEC) in resonance at prototype scale (1:1) and at model scale (1:16). Three simulation types were used: Reynolds Averaged Navier-Stokes (RANS), Euler and the linear radiation-diffraction method (linear). Results show that when the wave steepness is doubled, the response reduction is: (i) 3% due to the nonlinear mooring response and the Froude-Krylov force; (ii) 1-4% due to viscous forces; and (iii) 18-19% due to induced drag and non-linear added mass and radiation forces. The effect of the induced drag is shown to be largely scale-independent. It is caused by local pressure variations due to vortex generation below the body, which reduces the total pressure force on the hole. Euler simulations are shown to be scale-independent and the scale effects of the WEC are limited by the purely viscous contribution (1-4%) for the two waves studied. We recommend that experimental model scale test campaigns of WECs should be accompanied by RANS simulations, and the analysis complemented by scale-independent Euler simulations to quantify the scale-dependent part of the nonlinear effects.
A coupling between a dynamic mooring solver based on high-order finite element techniques (MooDy) and a radiation-diffraction based hydrodynamic solver (WEC-Sim) is presented. The high-order scheme gives fast convergence resulting in high-resolution simulations at a lower computational cost. The model is compared against a lumped mass mooring code (MoorDyn) that has an existing coupling to WEC-Sim. The two models are compared for a standard test case and the results are similar, giving confidence in the new WEC-Sim-MooDy coupling. Finally, the coupled model is validated using experimental data of a spread moored cylinder with good agreement.
Injection of water into wells is a common practice in offshore oil and gas installations, and here as in many other industries the water has to be deaerated before it is sent through miles of pipelines to reduce the risk of corrosion in those pipelines and other downstream equipment. It requires extremely low concentrations of dissolved oxygen for the corrosion of metals to begin, and removing the dissolved oxygen is currently done in large vacuum deaeration towers, a highly energy demanding process, along with additional injection of chemical oxygen scavengers. In many instances these processes are controlled in a feed-forward manner, where the operators rely on infrequent sampling and corresponding measurements to control the process. The possibilities for optimization in this field are thus numerous. The main challenges are online measurements of dissolved oxygen and their use in feedback control. This article gives a brief review of the state-of-the-art and investigates the potential of using dissolved oxygen as a reliable feedback parameter, taking inspiration from onshore waste water industries which have been dealing with dissolved oxygen feedback control since the 1970's.
For the assessment of experimental measurements of focused wave groups impacting a surface-piecing fixed structure, we present a new Fully Nonlinear Potential Flow (FNPF) model for simulation of unsteady water waves. The FNPF model is discretized in three spatial dimensions (3D) using high-order prismatic - possibly curvilinear - elements using a spectral element method (SEM) that has support for adaptive unstructured meshes. This SEM-FNPF model is based on an Eulerian formulation and deviates from past works in that a direct discretization of the Laplace problem is used making it straightforward to handle accurately floating structural bodies of arbitrary shape. Our objectives are; i) present detail of a new SEM modelling developments and ii) to consider its application to address a wave-body interaction problem for nonlinear design waves and their interaction with a model-scale fixed Floating Production, Storage and Offloading vessel (FPSO). We first reproduce experimental measurements for focused design waves that represent a probably extreme wave event for a sea state represented by a wave spectrum and seek to reproduce these measurements in a numerical wave tank. The validated input signal based on measurements is then generated in a NWT setup that includes the FPSO and differences in the signal caused by nonlinear diffraction is reported.
This paper investigates the optimal control solution using MPC for a typical offshore topside de-oiling process. By considering the combination of the upstream three-phase gravity separator and the downstream de-oiling hydrocyclone set-up as one integrated plant, the plant-wide control problem is formulated and handled using MPC technology. The de-oiling dynamics of the hydrocyclone are estimated via system identification while the key dynamics of the considered gravity separator are modeled based on mass balance and experimental parameter estimation. The developed MPC solution is simulated and experimentally validated via a lab-scaled pilot plant. The comparison of performances of the MPC controlled system with those of a PID controlled system, which emulates the commonly deployed control solution in most current installations, shows the promising results in optimally balancing the gravity separator's (level) control and hydrocyclone's (PDR) control.