Fouling release coatings (FRCs) can become damaged and diminished over exposure. Quantifying adverse effect of scratches on FRCs is crucial for damage control. This study investigated the effect of four pre-defined scratches on the re-fouling of a silicone-based FRC (SiFR) undergoing underwater cleaning utilizing a novel automated underwater cleaning system (AUCS). Moreover, barnacle adhesion and coating detachment formation of scratched SiFR were evaluated. Field testing at the CoaST Maritime Test Centre (CMTC) demonstrated that the scratches varying in depths and widths can significantly affect the biofouling behavior and cleaning efficiency of SiFR surface. For wide scratches (i.e. 3-mm-wide), hard fouling (e.g. barnacles, mussels) was more prone to accumulate, and underwater cleaning was effective in preventing hard fouling but not soft fouling on SiFR surface. Additionally, the re-fouling and cleaning difficulty of hard fouling increased with the depth of wide scratches. For narrow scratches (i.e. <50-μm-wide), SiFR was primarily attached by soft fouling (e.g. biofilm, algae), and underwater cleaning performed positive fouling resistance of algae but not biofilm on SiFR surface. Besides, algae became difficult to remove with the depth of narrow scratches. Notably, biweekly cleaning proved to be highly effective in biofouling control of SiFR with narrow and shallow scratches.
The effectiveness of fouling release coatings (FRCs) may diminish over time in the seawater. Underwater cleaning of FRCs in service is crucial for biofouling control. This study investigated the effects of cleaning parameters (brush moving speed, cleaning force and frequency) on a silicone-based FRC (SiFR) aged for 2 months (A2-SiFR) and 13 months (A13-SiFR), simulating the short-term and long-term FRCs in service. Fouling resistance, re-fouling and cleaning efficiency utilizing a self-designed automated underwater cleaning system (AUCS) were examined. Moreover, coating surface characterization, including visual appearance condition, roughness, water contact angle were evaluated on the testing surfaces. Field testing at the CoaST Maritime Test Centre (CMTC) demonstrated that underwater cleaning exhibited positive effect on the long-term fouling control performance of aged FRCs. Besides, stronger cleaning force, slower moving speed and biweekly cleaning led to better fouling resistance. No significant damages were observed on A2-SiFR surface, while regular spiral and circular scratches appeared on A13-SiFR surface. The damages led to adverse effects on fouling resistance, re-fouling and cleaning efficiency of algae on the cleaned A13-SiFR surface, affecting the coating performance more than cleaning parameters. Despite these damages, the cleaned surfaces still exhibited a higher fouling resistance compared with the ones without cleaning.
A number of solutions, with varying efficiency, have been proposed to mitigate discards. In this paper twelve mitigation measures were reviewed by their strengths and weaknesses, along with opportunities and threats, they might entail. How mitigation methods could either support or counteract others was also reviewed. The analyses of the mitigation measures are based on expert knowledge and experience and supported with existing literature. Discarding is highly variable and is influenced by numerous biological, technical and operational factors as well as social and economic drivers. These influences need to be carefully considered when designing management approaches. Finally, all reforms must be carefully considered within the context of a broader management system. The full management system needs to be thought of coherently to create an incentive framework that motivates fishers to avoid unwanted catches. It is only in this setting that discard mitigation methods may be potentially effective.
The costs of buying tonnage – whether new built or second hand – are so high that most Owners will need the assistance of Financers in order to be able to make the purchase. This raises several legal questions regarding ship’s finance. This article will provide a discussion of certain aspects of ships’ finance under Danish Law relevant to the charterparty trade.
The factual starting point for the paper is that a vessel is working in or intended to work in the charterparty trade, most particularly under long term time charterparties or Contracts of Affreightment. In such a situation, we find a tri-party relationship between the Financers, the Owners and the Charterers. When things are well, the interests of these three parties are on a par. The Charterers wish to use the vessel in order to make a profit, enabling them to pay the Owners. The Owners, receiving the hire or freight, are able to pay the crew, maintain the vessel and pay the Financers. However, the moment the financial stability of the Owner or the Charterer is threatened, the three parties will tend to have conflicting interests. The Financers, if unpaid, may wish to sell the vessel in order to cover at least some of their losses. The Charterers may wish to continue the use of the vessel, which may be inconsistent with a (forced) sale. Alternatively, the Charterers may wish to be freed of their obligations under the charterparty if the Owner enters into receivership or other types of insolvency proceedings. They may not be comfortable with e.g. having the Owners estate in bankruptcy running the vessel. And ultimately the Owners estate may wish to reconstruct the company in order to stay in business, for which end keeping the vessel as an asset and the income flowing from a (continued) charterparty may be a precondition.
The paper will discuss the problem with the starting point in Danish law on the subject, and investigate whether Danish law is apt to protect the conflicting interests of the three parties. However, the paper will make comparisons to other laws, mainly English law and Norwegian law. Also, the paper will discuss the general problems with the definitions of how a working vessel should generally be considered in the eyes of the law (is it simply any piece of chattels or is it more akin to a whole production facility?) and as well as whether the service provided by both owners and charterers under a charterparty should be considered personal or generic. Thus, although the paper uses Danish law as a starting point, it provides points of discussion of more general interest.
The paper ultimately concludes that Danish law does provide an adequate protection and balancing of the interest of the parties, but that uncertainties and the general inaccessibility of the law must be considered to restrict its use to the full – to the detriment of market interests.
Slugging flow in offshore oil & gas multi-phase transportation pipelines cause big challenges as the flow regime induces flow and pressure oscillations in the multi-phase pipelines. The negative impacts of the most severe slugs are significant and thus the elimination of slugging flow in the pipelines is a highly investigated topic. To eliminate the slug in an online manner real-time slug detection methods are often required. Traditionally topside pressure transmitters upstream of a 3-phase separator have been used as the controlled variable. In this paper Electrical Resistivity Tomography (ERT) has been examined as an alternative to the traditional pressure transmitters. A lab-scaled testing facility has been constructed in order to obtain test data from an ERT transmitter with 12 probes. Different flow regimes have been generated by a pump and a compressor where 2-phase flow can be tested. Based on the results, the study concludes that the ERT is able to detect the slug very well when the oil and water are well mixed. Furthermore, the traditional pressure transmitters have the limitation that pressure variations can be caused by other operating conditions than slug, such as change in the back pressure from control valves. The biggest limitation using ERT is the lack of ability to distinguish between gas and oil, and thus the ERT can only be used as an effective slug detect measurement when the oil-to-water ratio is low.
The upstream offshore multi-phase well-pipeline-riser installations are facing huge challenges related to slugging flow: An unstable flow regime where the flow rates, pressures and temperatures oscillate in the multi-phase pipelines. One typical severe slug is induced by vertical wells or risers causing the pressure to build up and hence originates the oscillating pressure and flow. There exist many negative consequences related to the severe slugging flow and thus lots of investments and effort have been put into reducing or completely eliminating the severe slug. This paper reviews in detail the state-of-the-art related to analysis, detection, dynamical modeling and elimination of the slug within the offshore oil & gas Exploration and Production (E&P) processes. Modeling of slugging flow has been used to investigate the slug characteristics and for design of anti-slug control as well, however most models require specific facility and operating data which, unfortunately, often is not available from most offshore installations. Anti-slug control has been investigated for several decades in the oil & gas industry, but many of these existing methods suffer the consequent risk of simultaneously reducing the oil & gas production. This paper concludes that slug is a well defined phenomenon, but even though it has been investigated for several decades the current anti-slug control methods still have problems related to robustness. It is predicted that slug-induced challenges will be even more severe as a consequence of the longer vertical risers caused by deep-water E&P in the future.
The severe slugging flow is always challenging in oil & gas production, especially for the current offshore based production. The slugging flow can cause a lot of potential problems, such as those relevant to production safety, fatigue as well as capability. As one typical phenomenon in multi-phase flow dynamics, the slug can be avoided or eliminated by proper facility design and control of operational conditions. Based on a testing facility which can emulate a pipeline-riser or a gas-lifted production well in a scaled-down manner, this paper experimentally studies the correlations of key operational parameters with severe slugging flows. These correlations are reflected through an obtained stable surface in the parameter space, which is a natural extension of the bifurcation plot. The maximal production opportunity without compromising the stability is also studied. Relevant studies have already showed that the capability, performance and efficiency of anti-slug control can be dramatically improved if these stable surfaces can be experimentally determined beforehand.
The current offshore oil & gas multi-phase production and transportation installations have big challenges related to the slugging flow: An unstable multi-phase flow regime where the flow rates, pressures and temperatures oscillate in the considered processes. Slug can be caused by different operating conditions and installation structures. The most severe slugs are often induced in long vertical risers or production wells, where liquid blocks gas at the riser/well base and correspondingly it causes the pressure to accumulate and hence originates the oscillating performance. There are many severe consequences to the production processes because of the slugging flow. This paper reviews some observed latest status and key challenges about slug detection, dynamical modeling and elimination of slugging flows. Mathematical modeling of slug has been used to investigate the slug mechanism and anti-slug control. Most of available models are based on mass-balance formulations, which often require sufficient data for reliable parameter tuning/identification. Slug elimination and control have been investigated for many years and there exist many solutions to eliminate the slug, but some of these methods can simultaneously reduce the oil & gas production, which is a very big concern as the production rate is the key evaluation parameter for offshore production. We conclude that the slugging flow is a well-defined phenomenon, even though this subject has been extensively investigated in the past decades, the cost-effective and optimal slug modeling and control are still open topics with many related challenges.
Slugging flow in the offshore oil & gas production attracts a lot of attention due to its limitation of production rate, periodic overload on processing facilities, and even direct cause of emergency shutdown. This work aims at two correlated objectives: (i) Preventing slugging flow; and meanwhile, (ii) maximizing the production rate at the riser of an offshore production platform, by manipulating a topside choke valve through a learning switching model-free PID controller. The results show good steady-state performance, although a long settling time due to the unknown reference for no slugging flow.
Maritime transport is the most energy-effective mode to move large amounts of goods around the world. Hauling cargo via waterway produces an enormous quantity of greenhouse gas emissions. Vessel fuel efficiency directly influences ship emissions by affecting the amount of burnt fuel. Optimizing ships operating in waves rather than in calm water conditions could decrease the fuel consumption of vessels. In particular, ship propellers are traditionally designed neglecting dynamic conditions such as time-varying wake distribution and propulsion factors, propeller speed fluctuations, ship motions, and speed loss. The effect of waves on the propeller performance can be evaluated using both a quasi-steady and a fully-unsteady approach. The former is a fast computational approximation method based on the assumption that the ratio of propeller angular frequency to wave encounter frequency is sufficiently large. The latter provides a complete representation of the propeller dynamics, but it is computationally expensive. The purpose of this paper is to compare the propeller performance in the presence of waves using the quasi-steady and the fully unsteady approach. This analysis is performed by observing the differences in unsteady propeller forces, cavitation volume, and hull pressure pulses between the two approaches. The full-scale KVLCC2 propeller is utilized for the investigation. Results show a good agreement between the quasi-steady and the fully-unsteady approach in the prediction of the temporal mean and the fluctuation amplitude of KT and KQ, the cavity volume variation, and the hull pressure pulses. Therefore, for the considered operating conditions, the quasi-steady approach can be used to compute the propeller performance in waves.