For design validation of offshore structures and conceptualisation of wave energy converters, physical model testing performed in wave basin laboratories is often applied. In such cases, knowledge about the wave conditions is of great significance. For validation of the wave condition in such tests, different methods for estimation of the directional wave spectra may be applied. However, different assumptions are imposed in the methods and deviations here from providing uncertainties in the results. The following paper quantifies the influence of nonlinear effects on the accuracy of the estimated directional wave spectra. This is done by analysis of idealised, synthetically generated waves based on second order wave theory and secondly with simplified amplitude dispersion included. The present analyzes show that the uncertainties of the directional wave spectra are proportional to the level of nonlinearity present in the wave field.
This paper analyzes the nonlinear forces on a moored point-absorbing wave energy converter (WEC) in resonance at prototype scale (1:1) and at model scale (1:16). Three simulation types were used: Reynolds Averaged Navier-Stokes (RANS), Euler and the linear radiation-diffraction method (linear). Results show that when the wave steepness is doubled, the response reduction is: (i) 3% due to the nonlinear mooring response and the Froude-Krylov force; (ii) 1-4% due to viscous forces; and (iii) 18-19% due to induced drag and non-linear added mass and radiation forces. The effect of the induced drag is shown to be largely scale-independent. It is caused by local pressure variations due to vortex generation below the body, which reduces the total pressure force on the hole. Euler simulations are shown to be scale-independent and the scale effects of the WEC are limited by the purely viscous contribution (1-4%) for the two waves studied. We recommend that experimental model scale test campaigns of WECs should be accompanied by RANS simulations, and the analysis complemented by scale-independent Euler simulations to quantify the scale-dependent part of the nonlinear effects.
This paper reports on a benchmark study based on small-scale (1:50) measurements of a single, oscillating water column chamber mounted sideways in a long flume. The geometry of the OWCchamber is extracted from a barge-like, attenuator- type floating concept “KNSwing” with 40 chambers targeted for deployment in the Danish part of the North Sea. In addition to traditional two-way energy extraction we also consider one-way energy extraction with passive venting and compare chamber response, pressures and total absorbed energy between the two methods. A blind study was established for the numerical modeling, with participants applying several implementations of weakly nonlinear potential flow theory and commercial Navier–Stokes solvers (CFD). Both compressible and incompressible models were used for the air phase. Potential flow calculations predict more energy absorption near the chamber resonance for one-way absorption than for two-way absorption, but the opposite is found from the experimental measurements. This outcome is mainly attributed to energy losses in the experimental passive valve system, but this conclusion must be confirmed by better experimental measurements. Modeling the one-way valve in CFD proved to be very challenging and only one team was able to provide results which were generally closer to the experiments. The study illustrates the challenges associated with both numerical and experimental analysis of OWC chambers. Air compressibility effects were not found to be important at this scale, even with the large volume of additional air used for the one-way case.
The paper presents incompressible Navier-Stokes simulations of the dynamics of a floating wave energy converter (WEC) coupled to a high-order finite element solver for cable dynamics. The coupled model has very few limiting assumptions and is capable of capturing the effects of breaking waves, green water loads on the WEC as well as non-linear mooring forces and snap loads, all of which are crucial for correct estimates of the extreme loads acting on the system in violent seas. The cable dynamics model has been developed as a stand-alone library that can be coupled to any body motion solver. In this study the open-source CFD package OpenFOAM has been employed. Preliminary test cases using incident regular Stoke's 5th order waves are presented, both for wave heights corresponding to operational conditions of the WEC as for a more severe condition in survival mode. It is illustrated that the coupled model is able to capture the complicated force propagation in the mooring cables.
Floating wave energy converters (WECs) operating in the resonance region are strongly affected by non-linearities arising from the interaction between the waves, the WEC motion and the mooring restraints. To compute the restrained WEC motion thus requires a method which readily accounts for these effects. This paper presents a method for coupled mooring analysis using a two-phase Navier-Stokes (VOF-RANS) model and a high-order finite element model of mooring cables. The method is validated against experimental measurements of a cylindrical buoy in regular waves, slack-moored with three catenary mooring cables. There is overall a good agreement between experimental and computational results with respect to buoy motions and mooring forces. Most importantly, the coupled numerical model accurately recreates the strong wave height dependence of the response amplitude operators seen in the experiments.
With increasing demand for renewable energy resources, the development of alternative concepts is still ongoing. The wave energy sector is still in vast development on the way to contribute to the energy production world wide. The present study presents the development of the Exowave wave energy converter made so far. A numerical model has been established supported by wave flume tests performed at Aalborg University during the first phase of the development. Furthermore, a successful open sea demonstration has been performed on 7 meters of water at Blue Accelerator, Belgium, from which the concept has been proven. As part of the ongoing research, verification of the numerical model will be made through experimental testing in the wave tank of Aalborg University, and an open sea demonstration at 14 meters of water depth will be executed off the coast of Hanstholm, Denmark.
Mooring systems are required to keep floating wave energy converters (WECs) on station. The mooring concept might impact the performance of the WEC, its cost and its integrity. With the aim of clarifying the pros and cons of different mooring designs, we present the results from physical model experiments of three different mooring concepts in regular and irregular waves, including operational and survival conditions. The parameters investigated are the tension in the cables, the motions of the device in the different degrees of freedom and the seabed footprint in each case. We can see that the mooring system affects the performance of the wave energy converter, but the magnitude of the impact depends on the parameter analysed, on the mode of motion studied and on the conditions of the sea. Moreover, different configurations have similar performances in some situations and the choice of one over another might come down to factors such as the type of soil of the seabed, the spacing desired between devices, or environmental impacts. The results of our experiments provide information for a better selection of the mooring system for a wave energy converter when several constraints are taken into account (power production, maximum displacements, extreme tensions, etc).
The following report presents the results of the experimental testing of the Exowave wave energy converter (WEC) performed in September 2023 at the Ocean and Coastal Engineering Laboratory at Aalborg University, Denmark. The model tests are performed based on the current design of the WEC35 Exowave floater as part of the project 250 MW bølgekraft I den danske Nordsø før 2030 – fase 1 supported by the Danish Energy Agency under the Energy Technology Development and Demonstration Program (EUDP) contract number 64022-1062.
High-fidelity simulations using computational fluid dynamics (CFD) for wave-body interaction are becoming increasingly common and important for wave energy converter (WEC) design. The open source finite volume toolbox OpenFOAM® is one of the most frequently used platforms for wave energy. There are currently two ways to account for moving bodies in OpenFOAM: (i) mesh morph-ing, where the mesh deforms around the body; and (ii) an overlooked mesh method where a separate body mesh moves on top of a background mesh. Mesh morphing is computationally efficient but may introduce highly deformed cells for combinations of large translational and rotational motions. The overlooked method allows for arbitrarily large body motions and retains the quality of the mesh. However, it comes with a substantial increase in computational cost and possible loss of energy conservation due to the interpolation. In this paper we present a straightforward extension of the spherical linear interpolation (SLERP) based mesh morphing algorithm that increases the stability range of the method. The mesh deformation is allowed to be interpolated independently for different modes of motion, which facilitates tailored mesh motion simulations. The paper details the implementation of the method and evaluates its performance with computational examples of a cylinder with a moonpool. The examples show that the modified mesh morphing approach handles large motions well and provides a cost effective alternative to overlooked mesh for survival conditions.
Floating Power Plant (FPP) develops a hybrid floating wind and wave energy device. Pitching Wave Energy Converters (WECs) interact with the supporting structure, amplifying the motion of the WECs within the design wave frequency range. In this work we focus on the effect of the chamber geometry – without the WEC – in amplifying the waves inside the chamber. The simulations are carried out using two-phase Navier-Stokes simulations. We investigate the wave propagation and the interaction between waves and the fixed support structure. The simulations are compared to experimental tests performed in the wave basin at Aalborg University.