Until now, wave-energy developers have focused on designing large machines for utility-scale electricity generation. While many concepts with good capture performance have been devised, significant commercial success has yet to be achieved in this market. Smaller wave energy converters (WECs) for specialist uses have received less attention. Emerging applications for these machines include powering sensors for ocean monitoring and providing energy for recharging maritime autonomous vehicles. Small reliable floating WECs can provide both the low levels of power required for these applications, and a surface platform for satellite
communications. Here, the key idea is to reduce costs and increase human safety by deploying small WECs to perform tasks that would otherwise require a ship. Developing small WECs for specialist uses provides a fast route to market, thereby creating a viable financial and technical base for the development of larger devices for applications where more power is required. This paper reports early results of time- and frequency-domain simulations of a compact WEC designed for monitoring the ocean environment.
This paper reports on a benchmark study based on small-scale (1:50) measurements of a single, oscillating water column chamber mounted sideways in a long flume. The geometry of the OWCchamber is extracted from a barge-like, attenuator- type floating concept “KNSwing” with 40 chambers targeted for deployment in the Danish part of the North Sea. In addition to traditional two-way energy extraction we also consider one-way energy extraction with passive venting and compare chamber response, pressures and total absorbed energy between the two methods. A blind study was established for the numerical modeling, with participants applying several implementations of weakly nonlinear potential flow theory and commercial Navier–Stokes solvers (CFD). Both compressible and incompressible models were used for the air phase. Potential flow calculations predict more energy absorption near the chamber resonance for one-way absorption than for two-way absorption, but the opposite is found from the experimental measurements. This outcome is mainly attributed to energy losses in the experimental passive valve system, but this conclusion must be confirmed by better experimental measurements. Modeling the one-way valve in CFD proved to be very challenging and only one team was able to provide results which were generally closer to the experiments. The study illustrates the challenges associated with both numerical and experimental analysis of OWC chambers. Air compressibility effects were not found to be important at this scale, even with the large volume of additional air used for the one-way case.
Physical wave basin tests with a focus on uncertainty estimation have been conducted on a sphere subjected to wave loads at Aalborg University as part of the effort of the OES Wave Energy Converters Modeling Verification and Validation (formerly, OES Task 10) working group to increase credibility of numerical modeling of WECs. The tests are referred to as the Kramer Sphere Cases, and the present note is dealing with wave excitation force tests on a fixed model. The present note is including details to facilitate CFD models which replicate the physical setup in detail.
Physical wave basin tests with a focus on uncertainty estimation have been conducted on a fixed sphere subjected to wave loads at Aalborg University as part of the effort of the OES Wave Energy Converters Modeling Verification and Validation (formerly, OES Task 10) working group to increase credibility of numerical modeling of WECs.
The present note defines an idealized test case formulated to accurately represent the physical tests in a simple way. The test case consists of a fixed, rigid sphere half submerged in water subjected to regular waves of three different levels of linearity. The objective of the present note is to allow for numerical tests of the idealized test case.
High-fidelity models become more and more used in the wave energy sector. They offer a fully nonlinear simulation tool that in theory should encompass all linear and nonlinear forces acting on a wave energy converter (WEC). Studies using high-fidelity models are usually focusing on validation of the model. However, a validated model does not necessarily provide reliable solutions. Solution verification is the methodology to estimate the numerical uncertainties related to a simulation. In this work we test four different approaches: the classical grid convergence index (GCI); a least-squares version (LS-GCI); a simplified version of the least-square method (SLS-GCI); and the ITTC recommended practice. The LS-GCI requires four or more solutions whereas the other three methods only need three solutions. We apply these methods to four different high-fidelity models for the case of a heaving sphere. We evaluate the numerical uncertainties for two parameters in the time domain and two parameters in the frequency domain. It was found that the GCI and ITTC were hard to use on the frequency domain parameters as they require monotonic convergence which sometimes does not happen due to the differences in the solutions being very small. The SLS-GCI performed almost as well as the SL-GCI method and will be further investigated.
For design validation of offshore structures and conceptualisation of wave energy converters, physical model testing performed in wave basin laboratories is often applied. In such cases, knowledge about the wave conditions is of great significance. For validation of the wave condition in such tests, different methods for estimation of the directional wave spectra may be applied. However, different assumptions are imposed in the methods and deviations here from providing uncertainties in the results. The following paper quantifies the influence of nonlinear effects on the accuracy of the estimated directional wave spectra. This is done by analysis of idealised, synthetically generated waves based on second order wave theory and secondly with simplified amplitude dispersion included. The present analyzes show that the uncertainties of the directional wave spectra are proportional to the level of nonlinearity present in the wave field.
The following report presents the results of the experimental testing of the Exowave wave energy converter (WEC) performed in September 2023 at the Ocean and Coastal Engineering Laboratory at Aalborg University, Denmark. The model tests are performed based on the current design of the WEC35 Exowave floater as part of the project 250 MW bølgekraft I den danske Nordsø før 2030 – fase 1 supported by the Danish Energy Agency under the Energy Technology Development and Demonstration Program (EUDP) contract number 64022-1062.
The design of wave energy converters should rely on numerical models that are able to estimate accurately the dynamics and loads in extreme wave conditions. A high-fidelity CFD model of a 1:30 scale point-absorber is developed and validated on experimental data. This work constitutes beyond the state-of-the-art validation study as the system is subjected to 50-year return period waves. Additionally, a new methodology that addresses the well-known challenge in CFD codes of mesh deformation is successfully applied and validated. The CFD model is evaluated in different conditions: wave-only, free decay, and wave–structure interaction. The results show that the extreme waves and the experimental setup of the wave energy converter are simulated within an accuracy of 2%. The developed high-fidelity model is able to capture the motion of the system and the force in the mooring line under extreme waves with satisfactory accuracy. The deviation between the numerical and corresponding experimental RAOs is lower than 7% for waves with smaller steepness. In higher waves, the deviation increases up to 10% due to the inevitable wave reflections and complex dynamics. The pitch motion presents a larger deviation, however, the pitch is of secondary importance for a point-absorber wave energy converter.
Wave excitation tests on a fixed sphere with the center at the still water level were carried out with three different physical wave basin setups. The tests were completed as a continued effort of the working group OES Wave Energy Converters Modeling Verification and Validation to increase confidence in numerical models of wave energy converters by generation of accurate benchmarks datasets for numerical model validation. An idealized test case with wave excitation of a fixed sphere to be used with the benchmarks was formulated. The three investigated physical wave basin setups included: 1) a six degree-of-freedom load cell mounted to the top of the sphere, 2) a bending beam force transducer mounted to the top of the sphere, and 3) a system of six pretensioned wires mounted to the top and bottom of the sphere with force transducers attached to each wire. The aim of the present paper is to identify the best representation of the idealized test case. To this end, the three experimental setups are inter-compared in terms of dynamic properties, sensitivity, and disturbances of the water phase from the presence of measurement equipment. Low inter-experiment variability was disclosed, ie, 5-8% depending on wave-nonlinearity, indicating accurate representations of the idealized test case across all setups. Setup 3 was found to be the more accurate representation and further work with this setup to release a public benchmark dataset was planned.
With increasing demand for renewable energy resources, the development of alternative concepts is still ongoing. The wave energy sector is still in vast development on the way to contribute to the energy production world wide. The present study presents the development of the Exowave wave energy converter made so far. A numerical model has been established supported by wave flume tests performed at Aalborg University during the first phase of the development. Furthermore, a successful open sea demonstration has been performed on 7 meters of water at Blue Accelerator, Belgium, from which the concept has been proven. As part of the ongoing research, verification of the numerical model will be made through experimental testing in the wave tank of Aalborg University, and an open sea demonstration at 14 meters of water depth will be executed off the coast of Hanstholm, Denmark.