This paper investigates the challenges associated with remote harmonic compensation in offshore wind power plants through long cables and transformers. The interaction between the grid network and the wind power plant network can lead to the amplification of certain harmonics and potentially resonant conditions. Hence, the plant developer is required to maintain the harmonic distortion at the point of common coupling within the planning level limits using harmonic compensation, which is usually done by static filters. In this paper an active damping compensation strategy with a STATCOM using emulation of using emulation of resistance at the harmonic frequencies of concern is analyzed. Finally the results are demonstrated using time domain simulations in PSCAD.
When an offshore wind power plant is connected to the grid, there is a risk of amplification of certain harmonics and appearance resonances at the point of connection due to the interaction between the grid network and the wind power plant network. Hence, the plant developer is obliged to maintain the harmonic distortion at the point of common coupling within the planning level limits using harmonic compensation, which is usually done by passive filters. In this paper a novel active harmonic compensation technique using voltage feedback from a non-local bus has been proposed and analyzed. Its effectiveness has been demonstrated through real time simulations on a test system model.
In a number of experiments and field tests of point absorbers, snap loads have been identified to cause damage on the mooring cables. Snap loads are basically propagating shock waves, which require special care in the numerical modeling of the mooring cable dynamics. In this paper we present a mooring cable model based on a conservative formulation, discretized using the Runge-Kutta discontinuous Galerkin method. The numerical model is thus well suited for correctly capturing snap loads. The numerical model is verified and validated using analytic and experimental data and the computed results are satisfactory.
Mooring systems are required to keep floating wave energy converters (WECs) on station. The mooring concept might impact the performance of the WEC, its cost and its integrity. With the aim of clarifying the pros and cons of different mooring designs, we present the results from physical model experiments of three different mooring concepts in regular and irregular waves, including operational and survival conditions. The parameters investigated are the tension in the cables, the motions of the device in the different degrees of freedom and the seabed footprint in each case. We can see that the mooring system affects the performance of the wave energy converter, but the magnitude of the impact depends on the parameter analysed, on the mode of motion studied and on the conditions of the sea. Moreover, different configurations have similar performances in some situations and the choice of one over another might come down to factors such as the type of soil of the seabed, the spacing desired between devices, or environmental impacts. The results of our experiments provide information for a better selection of the mooring system for a wave energy converter when several constraints are taken into account (power production, maximum displacements, extreme tensions, etc).
Floating wave energy converters (WECs) operating in the resonance region are strongly affected by non-linearities arising from the interaction between the waves, the WEC motion and the mooring restraints. To compute the restrained WEC motion thus requires a method which readily accounts for these effects. This paper presents a method for coupled mooring analysis using a two-phase Navier-Stokes (VOF-RANS) model and a high-order finite element model of mooring cables. The method is validated against experimental measurements of a cylindrical buoy in regular waves, slack-moored with three catenary mooring cables. There is overall a good agreement between experimental and computational results with respect to buoy motions and mooring forces. Most importantly, the coupled numerical model accurately recreates the strong wave height dependence of the response amplitude operators seen in the experiments.
A generic point-absorbing wave energy converter is modeled in CFD as a vertical cylinder, moored with a single catenary chain that is fully coupled through a dynamic mooring code. The method of choice is very complete and takes much of the non-linearities in the highly coupled system of the moored body into account. The paper presents numerical results compared with experimental data for surge, heave and pitch motion in both decay tests and regular waves. Further, the wave motion response of the cylinder is computed using both a viscous and a non-viscous formulation as a first attempt to quantify viscous effects. Results show a good match between numerical and experimental results in heave, while the surge and pitch motion are more difficult to reproduce. The mooring load cycle appearance compares well with the experiments in shape but gives higher peak values. Although made at low Keulegan-Carpenter numbers, the simulations show vortical structures due to the heave motion, and the resulting motions are clearly affected by the inclusion or exclusion of viscosity. More test-cases and detailed experimental results are needed for further quantification of the viscous impact on floating point absorbers.
Due to the presence of long high voltage cable networks, and power transformers for the grid connection, the offshore wind power plants (OWPPs) are susceptible to harmonic distortion and resonances. The grid connection of OWPP should not cause the harmonic distortion beyond the permissible limits at the point of common coupling (PCC). The resonance conditions should be avoided in all cases.
This paper describes the harmonic analysis techniques applied on an OWPP network model. A method is proposed to estimate the harmonic current compensation from a shunt-connected active power filter to mitigate the harmonic voltage distortion at the PCC. Finally, the harmonic distortions in the compensated and the uncompensated systems are compared to demonstrate the effectiveness of the compensation.
A numerical model (MOODY) for the study of the dynamics of cables is presented in Palm et al. (2013), which was developed for the design of mooring systems for floating wave energy converters. But how does it behave when it is employed together with the tools used to model floating bodies? To answer this question, MOODY was coupled to a linear potential theory code and to a computational fluid dynamics code (OpenFOAM), to model small scale experiments with a moored buoy in linear waves. The experiments are well reproduced in the simulations, with the exception of second order effects when linear potential theory is used and of the small overestimation of the surge drift when computational fluid dynamics is used. The results suggest that MOODY can be used to successfully model moored floating wave energy converters.
The paper presents incompressible Navier-Stokes simulations of the dynamics of a floating wave energy converter (WEC) coupled to a high-order finite element solver for cable dynamics. The coupled model has very few limiting assumptions and is capable of capturing the effects of breaking waves, green water loads on the WEC as well as non-linear mooring forces and snap loads, all of which are crucial for correct estimates of the extreme loads acting on the system in violent seas. The cable dynamics model has been developed as a stand-alone library that can be coupled to any body motion solver. In this study the open-source CFD package OpenFOAM has been employed. Preliminary test cases using incident regular Stoke's 5th order waves are presented, both for wave heights corresponding to operational conditions of the WEC as for a more severe condition in survival mode. It is illustrated that the coupled model is able to capture the complicated force propagation in the mooring cables.
Various sources of harmonic problems in large wind power plants (WPPs) and optimized harmonic mitigation methods are presented in this paper. The harmonic problems such as sources of harmonic emission and amplification as well as harmonic stability are identified. Also modern preventive and remedial harmonic mitigation methods in terms of passive and active filtering are described. It is shown that WPP components such as long HVAC cables and park transformers can introduce significant low-frequency resonances which can affect wind turbine control system operation and overall WPP stability as well as amplification of harmonic distortion. It is underlined that there is a potential in terms of active filtering in modern grid-side converters in e.g. wind turbines, STATCOMs or HVDC stations utilized in modern large WPPs. It is also emphasized that the grid-side converter controller should be characterized by sufficient harmonic/noise rejection and adjusted depending on WPPs to which it is connected.