The paper presents incompressible Navier-Stokes simulations of the dynamics of a floating wave energy converter (WEC) coupled to a high-order finite element solver for cable dynamics. The coupled model has very few limiting assumptions and is capable of capturing the effects of breaking waves, green water loads on the WEC as well as non-linear mooring forces and snap loads, all of which are crucial for correct estimates of the extreme loads acting on the system in violent seas. The cable dynamics model has been developed as a stand-alone library that can be coupled to any body motion solver. In this study the open-source CFD package OpenFOAM has been employed. Preliminary test cases using incident regular Stoke's 5th order waves are presented, both for wave heights corresponding to operational conditions of the WEC as for a more severe condition in survival mode. It is illustrated that the coupled model is able to capture the complicated force propagation in the mooring cables.
A generic point-absorbing wave energy converter is modeled in CFD as a vertical cylinder, moored with a single catenary chain that is fully coupled through a dynamic mooring code. The method of choice is very complete and takes much of the non-linearities in the highly coupled system of the moored body into account. The paper presents numerical results compared with experimental data for surge, heave and pitch motion in both decay tests and regular waves. Further, the wave motion response of the cylinder is computed using both a viscous and a non-viscous formulation as a first attempt to quantify viscous effects. Results show a good match between numerical and experimental results in heave, while the surge and pitch motion are more difficult to reproduce. The mooring load cycle appearance compares well with the experiments in shape but gives higher peak values. Although made at low Keulegan-Carpenter numbers, the simulations show vortical structures due to the heave motion, and the resulting motions are clearly affected by the inclusion or exclusion of viscosity. More test-cases and detailed experimental results are needed for further quantification of the viscous impact on floating point absorbers.
Floating wave energy converters (WECs) operating in the resonance region are strongly affected by non-linearities arising from the interaction between the waves, the WEC motion and the mooring restraints. To compute the restrained WEC motion thus requires a method which readily accounts for these effects. This paper presents a method for coupled mooring analysis using a two-phase Navier-Stokes (VOF-RANS) model and a high-order finite element model of mooring cables. The method is validated against experimental measurements of a cylindrical buoy in regular waves, slack-moored with three catenary mooring cables. There is overall a good agreement between experimental and computational results with respect to buoy motions and mooring forces. Most importantly, the coupled numerical model accurately recreates the strong wave height dependence of the response amplitude operators seen in the experiments.
Mooring systems are required to keep floating wave energy converters (WECs) on station. The mooring concept might impact the performance of the WEC, its cost and its integrity. With the aim of clarifying the pros and cons of different mooring designs, we present the results from physical model experiments of three different mooring concepts in regular and irregular waves, including operational and survival conditions. The parameters investigated are the tension in the cables, the motions of the device in the different degrees of freedom and the seabed footprint in each case. We can see that the mooring system affects the performance of the wave energy converter, but the magnitude of the impact depends on the parameter analysed, on the mode of motion studied and on the conditions of the sea. Moreover, different configurations have similar performances in some situations and the choice of one over another might come down to factors such as the type of soil of the seabed, the spacing desired between devices, or environmental impacts. The results of our experiments provide information for a better selection of the mooring system for a wave energy converter when several constraints are taken into account (power production, maximum displacements, extreme tensions, etc).
The following report presents the results of the experimental testing of the Exowave wave energy converter (WEC) performed in September 2023 at the Ocean and Coastal Engineering Laboratory at Aalborg University, Denmark. The model tests are performed based on the current design of the WEC35 Exowave floater as part of the project 250 MW bølgekraft I den danske Nordsø før 2030 – fase 1 supported by the Danish Energy Agency under the Energy Technology Development and Demonstration Program (EUDP) contract number 64022-1062.
High-fidelity simulations using computational fluid dynamics (CFD) for wave-body interaction are becoming increasingly common and important for wave energy converter (WEC) design. The open source finite volume toolbox OpenFOAM® is one of the most frequently used platforms for wave energy. There are currently two ways to account for moving bodies in OpenFOAM: (i) mesh morph-ing, where the mesh deforms around the body; and (ii) an overlooked mesh method where a separate body mesh moves on top of a background mesh. Mesh morphing is computationally efficient but may introduce highly deformed cells for combinations of large translational and rotational motions. The overlooked method allows for arbitrarily large body motions and retains the quality of the mesh. However, it comes with a substantial increase in computational cost and possible loss of energy conservation due to the interpolation. In this paper we present a straightforward extension of the spherical linear interpolation (SLERP) based mesh morphing algorithm that increases the stability range of the method. The mesh deformation is allowed to be interpolated independently for different modes of motion, which facilitates tailored mesh motion simulations. The paper details the implementation of the method and evaluates its performance with computational examples of a cylinder with a moonpool. The examples show that the modified mesh morphing approach handles large motions well and provides a cost effective alternative to overlooked mesh for survival conditions.
Mooring systems for floating wave energy converters often rely on floaters to allow for minimum restraints of the body motion in heavy. However, the inclusion of floaters also introduce possible slack-taut scenarios induced by the dynamic response of the floater in relation to the fair-lead point of the mooring. This can increase the occurrence of snap loads. The present study outlines the work to include floaters and sinks into a high-order discontinuous Galerkin model for mooring cable dynamics. Numerical simulations of a mooring leg adapted from the Waves4Power full-scale device are performed, and the results from varying the floater geometry are analyzed.
For this case the floater influence on the occurrence of snap loads was clearly evident. There is a strong correlation between floater pitch response and cable slack in the upper mooring cable. For a floater with constant buoyancy, increasing the floater height and thereby increasing the pitch inertia of the floater is shown to decrease the range of frequencies where cable slack occurs. It is illustrated that for some cases, changing floater geometry can avoid slack altogether. A careful design of the floater geometry can thus make a large difference for the dynamic load factor of the mooring system.
This paper presents the methods developed and key findings of the IWEC project performed by Ocean Harvesting Technologies AB (OHT). It aimed to reduce the levelized cost of energy (LCoE) of OHT’s wave energy converter InfinityWEC, by analysing how different key parameters impact cost and annual output using a model of a 100-MW array installation. Component-level cost functions were developed and mapped to key parameters and constraints of the system. A large number of system configurations were then evaluated with a numerically efficient 3 degree-of-freedom (DoF) nonlinear radiationdiffraction model in WEC-Sim along with OHT’s sea statetuned polynomial reactive control (PRC). The most promising configurations were identified and investigated in more detail. The configuration with the best LCoE were finally identified and analysed further, including estimation of the effect of changing the PRC to model predictive control, which resulted in 17-34% higher annual output and 12-23% lower LCoE. The final LCoE was found to be 93-162 EUR MWh at 100 MW installed capacity. An important finding from the study is that using simplified metrics such as CAPEX/ton was found to be irrelevant. Numerical wave tank testing, high-fidelity computational fluid dynamics (CFD), were used to tune the viscous drag of the 3 DoF WEC-Sim model. Applying verification and validation (V&V) techniques the CFD simulations showed a relatively large numerical uncertainty, but the average power and the motion responses were found to be sufficiently accurate.
A numerical model (MOODY) for the study of the dynamics of cables is presented in Palm et al. (2013), which was developed for the design of mooring systems for floating wave energy converters. But how does it behave when it is employed together with the tools used to model floating bodies? To answer this question, MOODY was coupled to a linear potential theory code and to a computational fluid dynamics code (OpenFOAM), to model small scale experiments with a moored buoy in linear waves. The experiments are well reproduced in the simulations, with the exception of second order effects when linear potential theory is used and of the small overestimation of the surge drift when computational fluid dynamics is used. The results suggest that MOODY can be used to successfully model moored floating wave energy converters.
The International Energy Agency Technology Collaboration Program for Ocean Energy Systems (OES) initiated the OES Wave Energy Conversion Modeling Task, which focused on the verification and validation of numerical models for simulating wave energy converters (WECs). The long-term goal is to assess the accuracy of and establish confidence in the use of numerical models used in design as well as power performance assessment of WECs. To establish this confidence, the authors used different existing computational modeling tools to simulate given tasks to identify uncertainties related to simulation methodologies: (i) linear potential flow methods; (ii) weakly nonlinear Froude–Krylov methods; and (iii) fully nonlinear methods (fully nonlinear potential flow and Navier–Stokes models). This article summarizes the code-to-code task and code-to-experiment task that have been performed so far in this project, with a focus on investigating the impact of different levels of nonlinearities in the numerical models. Two different WECs were studied and simulated. The first was a heaving semi-submerged sphere, where free-decay tests and both regular and irregular wave cases were investigated in a code-to-code comparison. The second case was a heaving float corresponding to a physical model tested in a wave tank. We considered radiation, diffraction, and regular wave cases and compared quantities, such as the WEC motion, power output and hydrodynamic loading.