Physical wave basin tests with a focus on uncertainty estimation have been conducted on a sphere subjected to wave loads at Aalborg University as part of the effort of the OES Wave Energy Converters Modeling Verification and Validation (formerly, OES Task 10) working group to increase credibility of numerical modeling of WECs. The tests are referred to as the Kramer Sphere Cases, and the present note is dealing with wave excitation force tests on a fixed model. The present note is including details to facilitate CFD models which replicate the physical setup in detail.
Simulating the free decay motion and wave radiation from a heaving semi-submerged sphere poses significant computational challenges due to its three-dimensional complexity. By leveraging axisymmetry, we reduce the problem to a two-dimensional simulation, significantly decreasing computational demands while maintaining accuracy. In this paper, we exploit axisymmetry to perform a large ensemble of Computational Fluid Dynamics (CFDs) simulations, aiming to evaluate and maximize both accuracy and efficiency, using the Reynolds Averaged Navier–Stokes (RANS) solver interFOAM, in the opensource finite volume CFD software OpenFOAM. Validated against highly accurate experimental data, extensive parametric studies are conducted, previously limited by computational constraints, which facilitate the refinement of simulation setups. More than 50 iterations of the same heaving sphere simulation are performed, informing efficient trade-offs between computational cost and accuracy across various simulation parameters and mesh configurations. Ultimately, by employing axisymmetry, this research contributes to the development of more accurate and efficient numerical modeling in ocean engineering.
Physical wave basin tests with a focus on uncertainty estimation have been conducted on a fixed sphere subjected to wave loads at Aalborg University as part of the effort of the OES Wave Energy Converters Modeling Verification and Validation (formerly, OES Task 10) working group to increase credibility of numerical modeling of WECs.
The present note defines an idealized test case formulated to accurately represent the physical tests in a simple way. The test case consists of a fixed, rigid sphere half submerged in water subjected to regular waves of three different levels of linearity. The objective of the present note is to allow for numerical tests of the idealized test case.
The International Energy Agency Technology Collaboration Program for Ocean Energy Systems (OES) initiated the OES Wave Energy Conversion Modeling Task, which focused on the verification and validation of numerical models for simulating wave energy converters (WECs). The long-term goal is to assess the accuracy of and establish confidence in the use of numerical models used in design as well as power performance assessment of WECs. To establish this confidence, the authors used different existing computational modeling tools to simulate given tasks to identify uncertainties related to simulation methodologies: (i) linear potential flow methods; (ii) weakly nonlinear Froude–Krylov methods; and (iii) fully nonlinear methods (fully nonlinear potential flow and Navier–Stokes models). This article summarizes the code-to-code task and code-to-experiment task that have been performed so far in this project, with a focus on investigating the impact of different levels of nonlinearities in the numerical models. Two different WECs were studied and simulated. The first was a heaving semi-submerged sphere, where free-decay tests and both regular and irregular wave cases were investigated in a code-to-code comparison. The second case was a heaving float corresponding to a physical model tested in a wave tank. We considered radiation, diffraction, and regular wave cases and compared quantities, such as the WEC motion, power output and hydrodynamic loading.
In a number of experiments and field tests of point absorbers, snap loads have been identified to cause damage on the mooring cables. Snap loads are basically propagating shock waves, which require special care in the numerical modeling of the mooring cable dynamics. In this paper we present a mooring cable model based on a conservative formulation, discretized using the Runge-Kutta discontinuous Galerkin method. The numerical model is thus well suited for correctly capturing snap loads. The numerical model is verified and validated using analytic and experimental data and the computed results are satisfactory.
A numerical model (MOODY) for the study of the dynamics of cables is presented in Palm et al. (2013), which was developed for the design of mooring systems for floating wave energy converters. But how does it behave when it is employed together with the tools used to model floating bodies? To answer this question, MOODY was coupled to a linear potential theory code and to a computational fluid dynamics code (OpenFOAM), to model small scale experiments with a moored buoy in linear waves. The experiments are well reproduced in the simulations, with the exception of second order effects when linear potential theory is used and of the small overestimation of the surge drift when computational fluid dynamics is used. The results suggest that MOODY can be used to successfully model moored floating wave energy converters.