A new power-to-X desulfurization technology has been examined. The technology uses only electricity to oxidize the hydrogen sulfide (H2S) found in biogas to elemental sulfur. The process works by using a scrubber where the biogas comes into contact with a chlorine containing liquid. This process is capable of removing close to 100% of H2S in biogas. In this paper a parameter analysis of process parameters has been carried out. In addition a long term test of the process has been performed. It has been found that the liquid flow rate has a small but notable influence on the process’ performance on removing H2S. The efficiency of the process largely depends on total amount of H2S flowing through the scrubber. As the H2S concentration increases, the amount of chlorine required for the removal process is also increased. A high amount of chlorine in the solvent may lead to unwanted side reactions.
Underwater radiated noise (URN) from ship propellers has attracted increasing interest in recent years due to its adverse environmental effects on marine life and their communication channels. The environmental concern to reduce shipping noise and the industrial requirements for faster computational tools are driving factors that promote research in the specialized domain of hydroacoustics. This thesis deals with the development of such a computationally efficient numerical tool, which can be used in the prediction of underwater radiated noise in the early design phase of propellers.
The numerical model is developed with two major objectives – versatility in assessing the relative contributions from the major propeller-noise generating mechanisms, and rapidity in prediction of overall noise behaviour. It uses the Farassat-1A solid-FWH formulation of the Ffowcs-Williams- Hawkings equation by defining equivalent acoustic sources on the propeller blade, sheet cavity and tip vortex cavity surfaces. In particular, the application of the solid-FWH formulation to the tip vortex cavity model is the major novelty in this thesis.
The hydrodynamic flow solution is obtained from a potential flow based solver ESPPRO, which includes analytical models of sheet cavitation and tip vortex cavitation. The hydroacoustic numerical model developed within this thesis, DoLPHiN, is a Python-based code that is primarily designed to accept input from ESPPRO; but during the research, the code has also been adapted to read input from the commercial, finite-volume-based Navier-Stokes solver, STAR-CCM+.
The numerical model implementations are verified through analytical case studies for simple geometrical shapes, such as a pulsating sphere and an oscillating cylindrical cavity. The verification study is further extended for propeller geometries by identifying approximate reference solutions in simplified operating conditions. The numerical tool is validated for industrial application through comparison of its noise prediction with model-scale and full-scale noise measurements. Specific characteristics of the propeller noise spectrum are identified in order to evaluate its noise prediction capabilities. The uncertainty factors involved when validating with experimental measurements are also explored in detail. Furthermore, a design study is presented, which shows potential use of the numerical tool in practical propeller design and optimization applications.
Marine flexible pipe/cables, such as umbilicals, flexible pipes and cryogenic hoses, are widely adopted in ocean engineering. The reinforcing armor layer in these pipe/cables is the main component for bearing loads, which is a typical multi-layer helically wound slender structure with different winding angles for different devices. There has been no general theoretical methodology to describe the tensile performance of these flexible pipe/cables. This paper first introduces a theory to solve the tensile mechanical behavior of a helically wound structure. Based on the curved beam theory, a solution of the tensile stress of a helically wound slender is derived. Then, the deformation mechanism of the marine flexible pipe/cables structure with different winding angles is studied. Through comparing theoretical and numerical results, the deformation characteristic of the helically wound slender structure is further explained. It is found that a sectional torsional deformation generates when the structure with a larger winding angle is under tension condition, while the sectional deformation of the structure with a smaller winding angle is mainly tension. Finally, a couple types of marine flexible pipe/cables under the tension condition are provided to analyze the mechanical performance and compare the difference between different theoretical models. The research conclusion from this paper provides a useful reference for the structural analysis and design of marine flexible pipe/cables.
Determining the key characteristics of a ship during the concept and preliminary design phases is a critical and intricate process. In this study, we propose an alternative to traditional empirical methods by introducing a model to estimate the main particulars of diesel-powered Z-Drive harbor tugboats. This prediction is performed to determine the main particulars of tugboats: length, beam, draft, and power concerning the required service speed and bollard pull values, employing Bayesian network and non-linear regression methods. We utilized a dataset comprising 476 samples from 68 distinct diesel-powered Z-Drive harbor tugboat series to construct this model. The case study results demonstrate that the established model accurately predicts the main parameters of a tugboat with the obtained average of mean absolute percentage error values; 6.574% for the Bayesian network and 5.795%, 9.955% for non-linear regression methods. This model, therefore, proves to be a practical and valuable tool for ship designers in determining the main particulars of ships during the concept design stage by reducing revision return possibilities in further stages of ship design.
This paper addresses the connection between added wave resistance and required propulsion power of ships, having focus on the early stage of new ship designs, notably tankers and bulk carriers. The paper investigates how mean added wave resistance affects the required torque of a fixed pitch propeller and thus also the operational conditions of a directly coupled main engine. The interest of the study has its background in the assessment of minimum propulsion power, and the study considers the prescriptive guidelines of the IMO as basis. Specifically, the study focuses on an assessment of the minimum forward speed attainable under consideration of the propeller light running margin and static load limits of engines in the early phase of new ship designs, where details of hull geometry are not available. The study considers three semi-empirical methods for predicting mean added wave resistance. All methods are known to be applied in the industry, emphasising that only methods relying solely on main particulars, together with information about sea state and advance speed, are of interest. The paper contains a case study used to illustrate the importance of the added wave resistance prediction with respect to the loading of the main engine. It is shown that, despite small absolute differences, the consequence in relation to the loading of the propeller and hereby the directly coupled main engine can be relatively large. Furthermore, the study illustrates that the propeller light running margin of a fixed pitch propeller directly coupled to the main engine has crucial influence on the attainable speed during adverse weather conditions.
Wind Propulsion Systems (WPS) for commercial ships are vital to achieving the IMO targets on energy efficiency and GHG emissions. Most WPS will operate in a hybrid mode alongside actual main propulsion units. This will affect the propeller and engine operating conditions and thus, their performance. The present paper discusses a preliminary assessment of commercial ship propellers and engine performance variation as a function of the wind power installed for two propeller plant types (Fixed Pitch Propeller, FPP, and Controllable Pitch Propeller, CPP) at constant speed operational mode. The contribution is based on empirical and analytical methods requiring minimal input data. It aims to provide general trends and contribute basic knowledge on this matter. A cost model is included for a cost-benefit assessment of both propeller types. This leads to advice on which systems to install as a function of WPS installation size.
Ship collision and grounding events constitute a major hazard for ship operations, and ship collision risk analyses have to be carried out for installations such as offshore structures for extraction of hydrocarbons, offshore wind farms, and bridges spanning waterways. This book provides assessment procedures for ship collision and grounding analysis and includes probabilistic methods for collision and grounding risk assessment, estimation of the energy released during collisions, and prediction of the extent of damage on the involved structures.
The main feature of the book is that it encapsulates reliable and fast analysis methods for collision and grounding assessment and the methods have been extensively validated with experimental and numerical results. In addition, all the described analysis methods include realistic calculation examples so as to provide confidence in their use to eventually conduct the required assessment according to the rules and design codes. The book is intended as a handbook for professionals and researchers in the industry dealing with design and analysis of ships and offshore structures. The book can also be used as a text book for postgraduate courses orientated towards the design and analysis of ship and offshore structures.
In recent years, shipboard microgrids (MGs) have become more flexible, efficient, and reliable. The next generations of future shipboards are required to be equipped with more focuses on energy storage systems to provide all-electric shipboards. Therefore, the shipboards must be very reliable to ensure the operation of all parts of the system. A reliable shipboard MG should be pro-tected from system faults through protection selectivity to minimize the impact of faults and facili-tate detection and location of faulty zones with the highest accuracy and speed. It is necessary to have an across-the-board overview of the protection systems in DC shipboards. This paper provides a comprehensive review of the issues and challenges faced in the protection of shipboard MGs. Furthermore, given the different types of components utilized in shipboard MGs, the fault behavior analysis of these components is provided to highlight the requirements for their protection. The protection system of DC shipboards is divided into three sub-systems, namely, fault detection, lo-cation, and isolation. Therefore, a comprehensive comparison of different existing fault detection, location, and isolation schemes, from traditional to modern techniques, on shipboard MGs is presented to highlight the advantages and disadvantages of each scheme.
In the present paper, the experimental data on wave run-up on slender monopiles from recently published small and large scale tests are reanalyzed using different methods for the wave analysis. The hypothesis is that the post processing has an impact on the results, due to limited depth and highly nonlinear waves in many of the tests. Thus, the identified maximum waves by a zero-down crossing analysis are highly influenced by the reflection analysis method as well as by bandpass filtering. The stagnation head theory with the run-up coefficient is adopted and new coefficients are presented. The hypothesis is verified, and the applied bandpass filter is identified as a large contributor to conservatism in previous studies, as the steep, nonlinear waves that produce the highest run-up can be heavily distorted by the bandpass filter.
This paper studies real-time deterministic prediction of wave-induced ship motions using the autocorrelation functions (ACFs) from short-time measurements, namely the instantaneous ACFs. The Prolate Spheroidal Wave Functions (PSWF) are introduced to correct the large lag time errors in the instantaneous sample ACF, together with a modification of the autocorrelation (AC) matrix for ensuring its positive definiteness. The validity of the PSWF-based ACFs is first examined by using the ship motion measurements from model experiment under stationary wave excitations. It is shown that the use of PSWFbased ACFs leads to better prediction accuracy than direct use of sample ACFs. The validation is then extended to ship motion prediction using in-service data from a container ship, and an improvement of the prediction accuracy by PSWF-based ACFs is again found. Finally, the effectiveness of use of the instantaneous ACFs for non-stationary wave-induced responses is highlighted by comparing with the prediction results based on the ACFs from long-time measurements.