Massive investments in offshore wind power generate significant challenges on how this electricity will be integrated into the incumbent energy systems. In this context, green hydrogen produced by offshore wind emerges as a promising solution to remove barriers towards a carbon-free economy in Europe and beyond. Motivated by the recent developments in Denmark with the decision to construct the world's first artificial Offshore Energy Hub, this paper investigates how the lowest cost for green hydrogen can be achieved. A model proposing an integrated design of the hydrogen and offshore electric power infrastructure, determining the levelised costs of both hydrogen and electricity, is proposed. The economic feasibility of hydrogen production from Offshore Wind Power Hubs is evaluated considering the combination of different electrolyser placements, technologies and modes of operations. The results show that costs down to 2.4 EUR per kg can be achieved for green hydrogen production offshore, competitive with the hydrogen costs currently produced by natural gas. Moreover, a reduction of up to 13 pct. of the cost of wind electricity is registered when an electrolyser is installed offshore shaving the peak loads.
A 3D fully nonlinear potential flow (FNPF) model based on an Eulerian formulation is presented. The model is discretized using high-order prismatic – possibly curvi-linear – elements using a spectral element method (SEM) that has support for adaptive unstructured meshes. The paper presents details of the FNPF-SEM development and the model is illustrated to exhibit exponential convergence. The model is then applied to the case of focused waves impacting on a surface-piecing fixed FPSO-like structure. Good agreement was found between numerical and experimental wave elevations and pressures.
Taking concrete steps towards a carbon-free society, the Danish Parliament has recently approved the establishment of the world's first two offshore energy hubs on Bornholm and on an artificial island in the North Sea. Being the two first-of-their-kind projects, several aspects related to the inclusion of these “energy islands” in the current market setup are still under discussion. To this end, this paper presents a first large-scale impact analysis of offshore hubs on the whole European power system and electricity market. Our study shows that energy hubs in the North Sea contribute to increase social welfare in Europe. However, when considering the impact on each country, benefits are not shared equally. To help the development of such projects, we focus on the identification of the challenges arising from the hubs. From a market perspective, we show how exporting countries are affected by the lower electricity prices and we point at heterogeneous consequences induced by new transmission capacity installed in the North Sea. From a system point of view, we show how the large amount of wind energy stresses conventional generators, which are required to become more flexible, and national grids, which cannot always accommodate large imports from the hubs.
In a premixed dual-fuel (DF) methane-diesel engine, the ignition of the lean premixed methane/air mixture starts with the assistance of a pilot diesel injection. Auto-ignition of pilot fuel is important as it triggers the subsequent combustion processes. A delay in the auto-ignition process may lead to misfiring, incomplete combustion, and thus higher greenhouse emissions due to methane slip. Hence, a better understanding of the auto-ignition process for the pilot fuel can help to improve the overall engine performance, combustion efficiency, and to lower exhaust emission levels. In the present study, large eddy simulation (LES) is used to investigate the auto-ignition process of micro-pilot diesel in premixed DF combustion in a constant volume combustion chamber (CVCC). The entire DF combustion processes including methane gas injection, methane/air mixing, pilot diesel injection, and ignition are simulated. The numerical model is validated against experimental data. The present numerical model is able to capture the ignition delay time (IDT) within a maximum relative difference of 7% to the measurements. A higher relative difference of 38% is obtained when methane gas injection and mixing are omitted in the simulation and the methane/air is assumed homogeneous. This demonstrates the importance of inhomogeneity pockets. To study the effects of temperature and methane inhomogeneities separately, different idealized inhomogeneities in temperature and methane distribution are considered inside the CVCC. The inhomogeneity in the temperature is observed to have a more profound influence on the IDT than the methane inhomogeneity. The inhomogeneity pockets of temperature advance the first-stage ignition and, subsequently, the second-stage ignition. A sensitivity analysis on the effect of inhomogeneity wavelength reveals that the larger wavelengths enhance the combustion due to the presence of pilot diesel jets in the desirable regions for a longer time duration.
Increasing concerns related to fossil fuels have led to the introducing the concept of emission-free ships (EF-Ships) in marine industry. One of the well-known combinations of green energy resources in EF-Ships is the hybridization of fuel cells (FCs) with energy storage systems (ESSs) and cold-ironing (CI). Due to the high investment cost of FCs and ESSs, the aging factors of these resources should be considered in the energy management of EF-Ships. This article proposes a nonlinear model for optimal energy management of EF-Ships with hybrid FC/ESS/CI as energy resources considering the aging factors of the FCs and ESSs. Total operation costs and aging factors of FCs and ESSs are chosen as problem objectives. Moreover, a stochastic model predictive control method is adapted to the model to consider the uncertainties during the optimization horizon. The proposed model is applied to an actual case test system and the results are discussed.
All-electric ships, and especially the hybrid ones with diesel generators and batteries, have attracted the attention of maritime industry in the last years due to their less emission and higher efficiency. The variant emission policies in different sailing areas and the impact of physical and environmental phenomena on ships energy consumption are two interesting and serious concepts in the maritime issues. In this paper, an efficient energy management strategy is proposed for a hybrid vessel that can effectively consider the emission policies and apply the impacts of ship resistant, wind direction and sea state on the ships propulsion. In addition, the possibility and impact of charging and discharging the carried electrical vehicles’ batteries by the ship is investigated. All mentioned matters are mathematically formulated and a general model of the system is extracted. The resulted model and real data are utilized for the proposed energy management strategy. A genetic algorithm is used in MATLAB software to obtain the optimal solution for a specific trip of the ship. Simulation results confirm the effectiveness of the proposed energy management method in economical and reliable operation of the ship considering the different emission control policies and weather condition impacts.
The utilization of green energy resources for supplying energy to ships in the marine industry has received increasing attention during the last years, where different green resource combinations and control strategies have been used. This article considers a ferry ship supplied by fuel cells (FCs) and batteries as the main sources of ship's power. Based on the designers' and owners' preferences, different scenarios can be considered for managing the operation of the FCs and batteries in all-electric marine power systems. In this article, while considering different constraints of the system, six operating scenarios for the set of FCs and batteries are proposed. Impacts of each proposed scenario on the optimal daily scheduling of FCs and batteries and operation costs of the ship are calculated using a mixed-integer nonlinear programming model. Model predictive control (MPC) is also applied to consider the deviations from hourly forecast demand. Moreover, since the efficiency of FCs varies for different output powers, the impacts of applying a linear model for FCs' efficiency are compared with the proposed nonlinear model and its related deviations from the optimal operation of the ship are investigated. The proposed model is solved by GAMS software using actual system data and the simulation results are discussed. Finally, detailed real-time hardware-in-the-loop (HiL) simulation outcomes and comparative analysis are presented to confirm the adaptation capability of the proposed strategy.
This work evaluates the hydrodynamic performance of an oscillating water column wave energy converter, with a focus on comparing conventional two-way energy capture to one-way energy capture where only the up- or down-stroke is used drive the turbine. Small-scale model test experiments are performed, and numerical calculations are made using weakly-nonlinear potential flow theory. The air turbine is represented experimentally by an orifice plate with a flow area equal to about 1% of the internal-chamber water-plane area. One-way energy capture by the experimental model is realized by incorporating a passive, low-inertia, non-return valve which vents the air inside the chamber on one half-cycle of the internal water-column oscillation. In the numerical calculations, there is little difference between the two venting configurations, due to the simplified weakly non-linear model. However, the experimental results show that up-stroke venting generally yields a higher power absorption than down-stroke venting and the two-way energy capture generally yields a higher power absorption compared to the one-way energy capture. The calculations agree well with the experiments for two-way absorption, but substantially over-predict the absorbed power in the one-way configuration. This is mainly attributed to the imperfect venting system in the physical model, but further tests and/or CFD calculations are needed to confirm this conclusion.
In this paper, full-scale data for two ships have been used for the comparison of five different added resistance methods. The effect of using separate wave spectra for wind waves and swell on performance prediction has been explored. The importance of the peak enhancement factor(γ) in the JONSWAP spectrum for added resistance computation has been studied. Simulation model including calm water resistance, added resistance and wind resistance has been used. Ships have been simulated in the same weather conditions and propeller speed as in the case of full-scale ships using different methods for added resistance. The performance of these methods has been quantified by comparing speed and power predictions with the full-scale data. The paper also discusses the challenges involved in using full-scale data for such a comparison because of difficulty in isolating the effect of added resistance in full-scale data. It was observed that three out of five methods were able to predict added resistance even in high waveheights. Even though these methods showed significantly different RAOs, its effect on speed and power prediction was minor. Simulation results were not sensitive to the choice of peak enhancement factor(γ) in the JONSWAP spectrum. There was minor improvement in results by using separate wave spectra for wind waves and swell instead of single wave spectrum for combined wind waves and swell.
This report includes a broad description of the findings from work package 2 in the EFFORT project and is made as the fulfillment of delivery L2.1 in the project. First an overall description of the Port of Hirtshals together with its infrastructure is given in chapter 1 together with some background aspect for the development of the Port of Hirtshals. In this chapter also the 5 companies who had shown their interest in participation in the project are described in more detail. Based on this as outcome of task 2.1 and described in chapter 2 an overall system architecture is set up for the existing industries at the Port of Hirtshals and next for the future expansion of the port. Based on the overall system architecture an adaptation of the system to the EU SGAM model is performed and explained. Then the overall set up of the data hub is briefly introduced, to see how it is related to the overall energy system set up. The final part documented for task 2.1 is two examples of sequence diagrams for first the processes in Forskerparken and next one which is valid for both the Fish Terminal, Lineage as well as Danish Salmon, since many of their electrical consuming processes here in an overall manner look the same.
In chapter 3 the base scenarios for the existing industries at Port of Hirtshals are set up. This is done based on information and wishes from the industries and the local Distribution System Operator (DSO), which is gained partly by bilateral discussions as well as on a workshop held with all the involved industries present at the same time. The scenarios will be described according to the IEC standard 62559-2, to ensure better utilization of the ideas in other projects, by applying a standard template known in this area.
Finally, in chapter 4 scenarios for the future expected extension of industries and activities at the Port of Hirtshals are set up. This is based on inputs from GPN, HH, NEN as well as Hjørring Municipality, Hirtshals Fjernvarme and from inputs from workshops with the existing industries at the port. Also here the IEC 62559-2 standard will be applied when describing the use cases.
The scenarios set up will later be used for the further development of the data hub, which is to be set up in the project, as well as for the model set up and control perspectives in the later WPs.