We present the results of a numerical model which has been developed for estimating the contribution to the methane slip from different sources in a four-stroke dual-fuel marine engine running on natural gas. The model is a thermodynamic three-zone zero-dimensional full engine cycle model and considers methane slip contributions from short-circuiting, crevices and wall quenching. The model is applied to analyze the methane slip from a four-stroke dual-fuel medium speed marine engine using natural gas as primary fuel. At low loads, wall quenching is found to be the dominant contribution to the methane slip. At full load, the wall quenching contribution is comparable to the level of the short-circuiting and crevice contributions which only vary relatively little with load. At 75% load, the contribution from short-circuiting is highest. In addition, we found that in-cylinder post-oxidation of unburned fuel remaining after the main combustion is negligible.
All-electric ships, and especially the hybrid ones with diesel generators and batteries, have attracted the attention of maritime industry in the last years due to their less emission and higher efficiency. The variant emission policies in different sailing areas and the impact of physical and environmental phenomena on ships energy consumption are two interesting and serious concepts in the maritime issues. In this paper, an efficient energy management strategy is proposed for a hybrid vessel that can effectively consider the emission policies and apply the impacts of ship resistant, wind direction and sea state on the ships propulsion. In addition, the possibility and impact of charging and discharging the carried electrical vehicles’ batteries by the ship is investigated. All mentioned matters are mathematically formulated and a general model of the system is extracted. The resulted model and real data are utilized for the proposed energy management strategy. A genetic algorithm is used in MATLAB software to obtain the optimal solution for a specific trip of the ship. Simulation results confirm the effectiveness of the proposed energy management method in economical and reliable operation of the ship considering the different emission control policies and weather condition impacts.
Due to the increasing impacts of ships pollutants on the environment and the preventive laws that are tightening every day, the utilization of all-electric ships is a recent emerging technology. Being a promising technology, the usage of fuel cells as the main energy resource of marine vessels is an interesting choice. In this article, an all-electric hybrid energy system with zero emission based on fuel cell, battery, and cold-ironing is proposed and analyzed. To this end, actual data of a ferry boat, including load profiles and paths, are considered to assess the feasibility of the proposed energy system. The configuration of the boat and energy resources as well as the problem constraints are modeled and analyzed. Finally, the boat's energy management in hourly form for a one-day period is implemented. The improved sine cosine algorithm is used for the power dispatch optimization, and all models are implemented in MATLAB software. Based on the analysis results, the proposed hybrid system and the energy management method have high performance as an applicable method for the marine vessels. In addition, to be a zero-emission ship, the proposed system has an acceptable energy cost.
This report provides an assessment on the prospects for offshore energy hubs. Four use cases have been developed and evaluated by respondents in a survey instrument for their forecasted time horizon to implementation and their business potential as opportunities for the maritime and offshore
industries. The report is produced by the PERISCOPE Group at Aarhus University for the PERISCOPE network.
Sustainable biofuel supply chain is a key to sustainable manufacturing and the future of production. Greener production is now becoming an order qualifier for the global competition. Modeling biofuel supply chains that achieve economic, social, and environmental feasibility is a challenge. This article develops biofuel platform planning and optimization that unifies biofuel product, production process and networks design into an umbrella of sustainable supply chain planning. A design of biofuel supply chain networks under various production paths is considered. The modeling results show that an optimum region of composition ratio between rice straws and waste cooking oils can be set within the range from 0% to 50%. Bio-diesel is favored over ethanol by occupying over 40% of the total biofuel outputs. However, ethanol yield is 99.1% and therefore it is sufficient to be directly mixed with gasoline at final depots. In terms of social contribution, it is estimated that the supply chain contribution to the case country GDP is about 0.17%. Looking at the above statistics, future research on global economic impacts and competitiveness of biofuel production is suggested.
For more than a century, conventional marine vessels spatter the atmosphere with CO2 emissions and detrimental particles when operated by diesel motors/generators. Fuel cells have recently emerged as one of the most promising emission-free technologies for the electrification of ship propulsion systems. In fuel cell-based ship electrification, the entire marine power system is viewed as a direct current (DC) microgrid (MG) with constant power loads (CPLs). A challenge of such settings is how to stabilize the voltages and currents of the ship’s grid. In this paper, we propose a new modified backstepping controller to stabilize the MG voltage and currents. Finally, to study the performance and efficiency of our proposal, we run an experiment simulation using dSPACE real-time emulator.
The selection of alternative energy sources for shipping can effectively mitigate the problems of high energy consumption and severe environmental problems caused by shipping. However, it is usually difficult for decision makers to select the most sustainable alternative energy source for shipping among multiple alternatives due to the complexity of considering different aspects of performances and the lack of information. This study developed a novel multi-criteria decision-making method that combines Dempster-Shafer theory and a trapezoidal fuzzy analytic hierarchy process for alternative energy source selection under incomplete information conditions. According to the developed method, nuclear power has been recognized as the most sustainable alternative energy source for shipping, followed by liquefied natural gas (LNG) and wind power, and sensitivity analysis reveals that the weights of the criteria have significant on the sustainability sequence of the three alternative energy sources for shipping. The developed method can be popularized for selecting the most sustainable alternative energy source despite incomplete information.
As of January 2015, the new maximum limit of fuel sulfur content for ships sailing within emission control areas has been reduced to 0.1%. A critical decision for ship owners in advance of the new limits was the selection of an abatement method that complies with the regulations. Two main options exist: investing in scrubber systems that remove sulfur dioxide emissions from the exhaust and switching to low-sulfur fuel when sailing in regulated waters. The first option would involve significant capital costs, while the latter would lead to operating cost increases because of the higher price of the fuel used. This paper presents a literature review of emissions abatement options and relevant research in the field. A cost–benefit methodology to assess emission reduction investments from ship owners is also presented. A study examined the effects of recent drops in bunker fuel price to the payback period of a potential scrubber investment. The results show that lower prices would significantly delay the payback period of such investments, up to two times in some cases. The case studies present the emissions generation through each option for representative short sea shipping routes. The repercussions of low-sulfur policies on large emission reduction investments including cold ironing are examined, along with implications of slow steaming for their respective payback periods. Recommendations are made for research in anticipation of future regulations and technological improvements.
This study concerns nitrogen based emissions from a hydrogen enriched ammonia fueled SI engine. These emissions deserve special attention as their formation may differ from conventional HC combustion due to the nitrogen content in the fuel. A range of experiments are conducted with a single cylinder 0.612 l CFR engine with a compression ratio varying from 7 to 15 using a fuel composition of 80 vol% NH3 and 20 vol% H2. Wet exhaust samples are analysed with an FT-IR. Emission measurements reveal that nitric oxide stem from other reaction paths than the dissociation of molecular nitrogen. This causes the NO emissions to peak around 35% rather than 10% excess air, as is typical in HC fueled SI-engines. However the magnitude of NO emissions are comparable to that of measurements conducted with gasoline due to lower flame temperatures. Nitrogen dioxide levels are higher when comparing with gasoline, but has a relatively low share of the total NOx emissions (3–4%). Nitrous oxide is a product of NH2 reacting with NO2 and NH reacting with NO. The magnitude is largely affected by ignition timing due to the temperature development during expansion and the amount of excess air, as increased oxygen availability stimulates the formation of the NH2 radical and the levels of NO2 are higher. Under ideal operating conditions (MBT ignition timing) N2O levels are very low. The dominating contributors to unburned ammonia are chamber crevices as the magnitude of these emissions is greatly affected by the compression ratio. However, levels are lower than required in order to eliminate all NOx emissions with a SCR catalyst.