Mooring failures significantly threaten the stability of Floating Offshore Wind Turbines (FOWT) under extreme environmental conditions. This study presents an innovative shared damping mooring system incorporating Seaflex dampers to improve structural stability and operational reliability. Dynamic simulations under 1-year and 50-year return period sea states demonstrate the system’s effectiveness. Under Ultimate Limit State (ULS) conditions, the system reduces surge displacement by 59%, pitch angle by 47%, and mooring line tension by 72%. Under Accidental Limit State (ALS) conditions, it mitigates load spikes, reduces drift displacement by 60%, and improves safety factors by 50%. The comparison shows chain and wire rope configurations have better load reduction performance in the shared damping scheme. Lightweight and adaptable, the Seaflex dampers enhance broad-spectrum damping without affecting platform buoyancy. This study provides a robust solution for improving FOWT safety and durability in harsh marine environments, enabling large-scale offshore wind energy development.
The design of wave energy converters should rely on numerical models that are able to estimate accurately the dynamics and loads in extreme wave conditions. A high-fidelity CFD model of a 1:30 scale point-absorber is developed and validated on experimental data. This work constitutes beyond the state-of-the-art validation study as the system is subjected to 50-year return period waves. Additionally, a new methodology that addresses the well-known challenge in CFD codes of mesh deformation is successfully applied and validated. The CFD model is evaluated in different conditions: wave-only, free decay, and wave–structure interaction. The results show that the extreme waves and the experimental setup of the wave energy converter are simulated within an accuracy of 2%. The developed high-fidelity model is able to capture the motion of the system and the force in the mooring line under extreme waves with satisfactory accuracy. The deviation between the numerical and corresponding experimental RAOs is lower than 7% for waves with smaller steepness. In higher waves, the deviation increases up to 10% due to the inevitable wave reflections and complex dynamics. The pitch motion presents a larger deviation, however, the pitch is of secondary importance for a point-absorber wave energy converter.
There are many uncertainties associated with the estimation of extreme loads acting on a wave energy converter (WEC). In this study we perform a sensitivity analysis of extreme loads acting on the Uppsala University (UU) WEC concept. The UU WEC consists of a bottom-mounted linear generator that is connected to a surface buoy with a taut mooring line. The maximum stroke length of the linear generator is enforced by end-stop springs. Initially, a Variation Mode and Effect Analysis (VMEA) was carried out in order to identify the largest input uncertainties. The system was then modeled in the time-domain solver WEC-SIM coupled to the dynamic mooring solver Moody. A sensitivity analysis was made by generating a surrogate model based on polynomial chaos expansions, which rapidly evaluates the maximum loads on the mooring line and the end-stops. The sensitivities are ranked using the Sobol index method. We investigated two sea states using equivalent regular waves (ERW) and irregular wave (IRW) trains. We found that the ERW approach significantly underestimates the maximum loads. Interestingly, the ERW predicted wave height and period as the most important parameters for the maximum mooring tension, whereas the tension in IRW was most sensitive to the drag coefficient of the surface buoy. The end-stop loads were most sensitive to the PTO damping coefficient.
The power output from many wave energy converters (WECs) is limited by a finite stroke length in the power take-off (PTO) mechanism. As the PTO approaches its maximum stroke length, an end-stop system needs to be engaged to avoid damage to the machinery. Still the on-set of the end-stop is a nonlinear trigger force, a stiff point in the system. In this respect it is similar to how snap loads in the mooring cables affect the system after a period of cable slack. This paper presents a detailed study into the dynamics of end-stop events and snap loads for a WEC. The WEC is a bottom-mounted linear generator connected to a surface buoy via a steel wire. By comparing a linear spring model with three dynamic mooring line models we conclude that large differences are observed in the low-tension and slack regions of the cable during moderate wave loads, while minor differences are seen in the estimated peak tension. By further varying end-stop parameters we observe that the peak tension in the line changes mildly with the axial stiffness for moderate wave heights. The peak tension is surprisingly unaffected by the introduction of a critical damping level to the end-stop system, despite the significant increase in end-stop force which causes the translator to come to a sudden stop. We discuss how the connection between maximum line force and end-stop parameters is highly dependent on the buoy position in the wave at the instant of end-stop onset.