Computational fluid dynamics (CFD) is becoming an increasingly popular tool in the wave energy sector, and over the last five years we have seen many studies using CFD. While the focus of the CFD studies have been on the validation phase, comparing numerically obtained results against experimental tests, the uncertainties associated with the numerical solution has so far been more or less overlooked. There is a need to increase the reliability of the numerical solutions in order to perform simulation based optimization at early stages of development. In this paper we introduce a well-established verification and validation (V&V) technique. We focus on the solution verification stage and how to estimate spatial discretization errors for simulations where no exact solutions are available. The technique is applied to the cases of a 2D heaving box and a 3D moored cylinder. The uncertainties are typically acceptable with a few percent for the 2D box, while the 3D cylinder case show double digit uncertainties. The uncertainties are discussed with regard to physical features of the flow and numerical techniques.
The present paper describes the work carried out in the project ’Mooring Solutions for Large Wave Energy Converters’, which is a Danish research project carried out in a period of three years from September 2014, with the aim of reducing cost of the moorings for four wave energy converters and improving the applied design procedure. The paper presents the initial layouts and costs and illustrates which solutions could potentially reduce cost. Different methods for analysis of the systems were applied, ranging from simple quasi-static analysis to full dynamic analysis and experimental work. The numerical methods were compared to the experimental data, and results showed significant underestimation of tensions in the quasi-static model while reasonable overestimation was found in the dynamic analysis even without major tuning of the model. The dynamic analysis has then been implemented in a meta-model based optimization process with the aim of optimizing the mooring layout for each WEC according to cost of the systems.
In a number of experiments and field tests of point absorbers, snap loads have been identified to cause damage on the mooring cables. Snap loads are basically propagating shock waves, which require special care in the numerical modeling of the mooring cable dynamics. In this paper we present a mooring cable model based on a conservative formulation, discretized using the Runge-Kutta discontinuous Galerkin method. The numerical model is thus well suited for correctly capturing snap loads. The numerical model is verified and validated using analytic and experimental data and the computed results are satisfactory.
Mooring systems are required to keep floating wave energy converters (WECs) on station. The mooring concept might impact the performance of the WEC, its cost and its integrity. With the aim of clarifying the pros and cons of different mooring designs, we present the results from physical model experiments of three different mooring concepts in regular and irregular waves, including operational and survival conditions. The parameters investigated are the tension in the cables, the motions of the device in the different degrees of freedom and the seabed footprint in each case. We can see that the mooring system affects the performance of the wave energy converter, but the magnitude of the impact depends on the parameter analysed, on the mode of motion studied and on the conditions of the sea. Moreover, different configurations have similar performances in some situations and the choice of one over another might come down to factors such as the type of soil of the seabed, the spacing desired between devices, or environmental impacts. The results of our experiments provide information for a better selection of the mooring system for a wave energy converter when several constraints are taken into account (power production, maximum displacements, extreme tensions, etc).
Floating wave energy converters (WECs) operating in the resonance region are strongly affected by non-linearities arising from the interaction between the waves, the WEC motion and the mooring restraints. To compute the restrained WEC motion thus requires a method which readily accounts for these effects. This paper presents a method for coupled mooring analysis using a two-phase Navier-Stokes (VOF-RANS) model and a high-order finite element model of mooring cables. The method is validated against experimental measurements of a cylindrical buoy in regular waves, slack-moored with three catenary mooring cables. There is overall a good agreement between experimental and computational results with respect to buoy motions and mooring forces. Most importantly, the coupled numerical model accurately recreates the strong wave height dependence of the response amplitude operators seen in the experiments.
A numerical model (MOODY) for the study of the dynamics of cables is presented in Palm et al. (2013), which was developed for the design of mooring systems for floating wave energy converters. But how does it behave when it is employed together with the tools used to model floating bodies? To answer this question, MOODY was coupled to a linear potential theory code and to a computational fluid dynamics code (OpenFOAM), to model small scale experiments with a moored buoy in linear waves. The experiments are well reproduced in the simulations, with the exception of second order effects when linear potential theory is used and of the small overestimation of the surge drift when computational fluid dynamics is used. The results suggest that MOODY can be used to successfully model moored floating wave energy converters.
The paper presents incompressible Navier-Stokes simulations of the dynamics of a floating wave energy converter (WEC) coupled to a high-order finite element solver for cable dynamics. The coupled model has very few limiting assumptions and is capable of capturing the effects of breaking waves, green water loads on the WEC as well as non-linear mooring forces and snap loads, all of which are crucial for correct estimates of the extreme loads acting on the system in violent seas. The cable dynamics model has been developed as a stand-alone library that can be coupled to any body motion solver. In this study the open-source CFD package OpenFOAM has been employed. Preliminary test cases using incident regular Stoke's 5th order waves are presented, both for wave heights corresponding to operational conditions of the WEC as for a more severe condition in survival mode. It is illustrated that the coupled model is able to capture the complicated force propagation in the mooring cables.